420 774 335 397 www.sharks-shop.cz
Stránka 51
With long-term use, the battery will become warm. Remove the battery before removing the
battery and allow the battery to cool down. Only use the battery with the label.
INSTALLING THE BOTTOM
●
Never use too thick a blade to allow the outer blade to touch the surface on the spindle.
●
Always remove the battery before installing the disc.
●
The disc is extremely sharp and care must be taken when handling it. Care must be taken
as the disc guard is flexible and, if released, may cause injury.
●
Turn the wheel guard to the fully open position and secure it in this position.
●
Press spindle lock button Fig. 3
●
CAUTION: To prevent damage to the spindle or spindle lock, allow the engine to stop
completely before the spindle lock is complete.
●
Remove the wheel bolt by turning it counterclockwise with the hexagon wrench while
holding the spindle lock button depressed Fig. 4
●
Install the saw blade into the lower blade guard and the spindle and make sure that the
direction of rotation arrow on the blade corresponds to the arrow of the direction of rotation
on the fixed guard arrow Fig. 5
NOTE: The saw teeth point up to the front of the saw.
●
Insert the blade pad. Press the spindle lock button, and then install the screw.
Tighten the wheel bolt firmly by turning it clockwise.
Note: Check the tightness of the wheel bolt before and after each use. Check bolt even
during operation.
●
Loosen the disc guard to cover the disc. Check the protective cover and make sure it works
properly. If everything is OK, your saw is ready for use.
REMOVING THE BOTTOM
Remove the battery from the saw.
●
Press the spindle lock button and turn the screw out.
●
Remove the washer.
●
Remove the disc.
Note: Use the parallel stop that is available when cutting.
BATTERY INSTALLATION
●
Warning! When installing parts, editing, cleaning, shipping or not using, always remove the
battery from the device.
●
Insert the battery into the tool base Fig. 7. Make sure that the battery is properly inserted
and secured before working.
Press the battery release button on the top of the battery and press down, Fig.8, and remove
the battery from the tool.
WORK OPERATION
●
Warning! Always check the bottom cover before each use.
●
Keep the disc clean and sharp.
●
Wear protective gloves when handling discs.
●
Keep your hands out of the blade. Do not touch the workpiece when the disc rotates.
●
The disc always rotates when the unit is switched off. Always wait for a complete stop.
●
The device must be in good condition to prevent damage to the instrument or injury to the
operator.
●
Use large panels as a background as shown in Figure 9 to minimize the risk of kickback.
●
Figure 10 shows an incorrect method of cutting large pieces of wood, which could result in
operator injury during this cutting. when cutting, the saw should be on a larger piece of
material and a smaller piece is cut off. Use a parallel stop or a support plate always when
cutting such material.
Summary of Contents for SH 18V Li-Ion
