13
0800 862 0453
14
www.sharkclean.eu
IMPORTANT: Loss of Suction may
occur
if foam filters are not cleaned
every 3 months. Rinse and allow to
air dry completely. Foam filters may
appear dirty after use - this is normal.
Fig. 19
Fig. 20
COMPONENT
MAINTENANCE SCHEDULE
Rinse and air dry every 3 months under normal use.
Empty each time you vacuum.
Pre-Motor Foam Filter
Dust Cup
Rinse and air dry every 3 months under normal use.
Pre-Motor Felt Filter
Clean once every 2 years or as needed.
Post-Motor HEPA Filter
1
2
3
4
CLEANING THE PRE-MOTOR FILTERS
1
Remove the dust cup.
2
Pull the 2 filters out from the top of the motor base.
(Fig. 22)
3
Rinse the filters thoroughly in lukewarm water until
the water runs clear.
DO NOT
put the filter in the washing machine or
dishwasher.
NOTE:
The material in the filter will discolor over
time. This is NORMAL and will not affect the
performance of the filter.
4
Squeeze out excess water and let air-dry for at least
24 hours before replacing. Do not use a hair dryer or
other heating methods to dry.
5
Place the felt filter in first, then the foam filter.
6
Replace the dust cup.
EMPTYING THE DUST CUP
The dust cup needs to be emptied each time you vacuum
and periodically during cleaning, when the dust cup
appears full.
1
Undo the latches on the sides of the dust cup by
lifting them up and outwards to remove the dust cup
from the motor base.
(Fig. 19)
2
Hold the dust cup over a trash receptacle and
press the bottom door release button.
(Fig. 20)
Tap gently to empty contents. Press the door shut
again until it clicks.
3
If needed, turn the dust cup upside down over the
trash receptacle and press the top door release
button.
(Fig. 21)
Tap gently to remove contents.
Use a dry cloth or paper towel to remove debris
stuck to the screen filter inside the dust cup. Press
the door shut again until it clicks.
4
Replace the dust cup on top of the motor base. Hook
the two latches onto the tabs on the sides of the
dust cup and push down to lock.
Screen
Filter
Fig. 21
Fig. 22
Pre-Motor
Foam Filter
Felt Filter
Post Motor
HEPA Filter
Maintenance
CAUTION:
Turn power off and unplug from outlet before servicing.
CLEANING THE POST-MOTOR HEPA FILTER
1
Remove the filter cover from the front of the vacuum
by pulling up on the tab and pulling the cover away
from the vacuum.
(Fig. 23)
2
Take out the HEPA filter by pulling it straight out.
3
Turn the filter over so that the dirty side is on the
bottom and vigorously tap it clean against a garbage
can to remove any dust.
(Fig. 24)
4
Wash the filter under the tap using lukewarm water
with the dirty side face down until the water runs
clear.
(Fig. 25)
DO NOT
put the filter in the washing machine or
dishwasher.
NOTE:
The material in the filter will discolor over
time. This is NORMAL and will not affect the
performance of the filter.
5
Allow the filter to air dry for 24 hours. Do not use a
hair dryer or other heating methods to dry.
6
Once the HEPA filter is dry, replace it back into the
vacuum.
7
Replace the cover by inserting the two tabs into the
holes at the top and then swinging the cover down
until it clicks into place.
Fig. 24
Fig. 23
Fig. 25
Fig. 26
a
CLEANING THE LARGE PET POWER BRUSH
1
Slide the locking latch
(a)
forward and gently tilt
brush housing upward to open.
(Fig. 26)
IMPORTANT:
DO NOT force; it will not open all the
way.
2
Carefully remove any blockage or debris.
3
Turn the power brush over to inspect the rotating
brush and cut away any build-up of hair or string
wrapped around the rotating bristle brush with
scissors.
(Fig. 27)
4
Push the housing back down and slide the locking
latch backward to lock.
Fig. 27
CAUTION:
Turn power off and unplug from outlet
before servicing.
Summary of Contents for NV350UKC
Page 1: ...NV350UKC Owner s guide ...
