background image

14

textile PaRtS
type

The textile and foam parts providing comfort to 

the SHARK Nano and the SHARK Raw make it 

easy for you to appreciate the performance of 

your helmet to the best.

The parts in contact with the skin are made 

in a fabric that is guaranteed to feel pleasant, 

to absorb perspiration well and to resist wear 

satisfactorily. We treat surfaces to limit the risk 

of mould and bacteria.

Always in one concerns of hygiene, the outer 

seal are treated against bacteria, what allows 

avoiding their proliferation when we put the 

helmet.

treatment

Warning: although they are selected for 

their quality of resistance and satisfactory 

wear, all the interior padding is subject to 

normal wear depending on use and care 

and maintenance, the length of use and also 

the degree of acidity of your perspiration.

If you note any wear, we advise you to replace 

the interior padding in order to keep your hel-

met perfectly clean and comfortable. 

textile PaRtS

Your SHARK supplier can propose you with 

replacement parts and also offer you cheek 

pads of different thicknesses and densities, 

should the standard selection not correspond 

to the contours of your face.

maintenance

The interior textile parts are washable; it is 

important to follow the instructions below 

scrupulously to avoid damaging them.
The cheek pads and head section must be 

hand washed in warm, soapy water (about 

30°). 

Do not use aggressive detergents but 

either a product for delicate materials in 

low dilution or household soap.

It is essential to dry textile and foam parts 

completely before using them. They must be 

dried at room temperature. Never iron textile 

parts. 
For parts with a leather appearance or textiles 

attached to safety elements, use a slightly 

damp sponge or cloth and household soap 

and rinse with clean water. 

Avoid allowing 

too much water to come into contact with 

polystyrene parts.

It is essential to ensure that all interior parts 

are perfectly dry before using the helmet.

Summary of Contents for Nano





















Reviews: