background image

19

5 years Warranty

You have recently purchased a SHARK helmet for your 

safety and pleasure. It has been designed with the grea-

test care to satisfy your every requirement. For your sa-

fety, and that of your passenger, you must respect all the 

rules of prudence when using your two-wheeled vehicle.

The SHARK 5-YEAR warranty guarantees the initial pur-

chaser that any possible manufacturing fault or material 

defect will be covered by the SHARK warranty.

limitations

If during the warranty period (5 years as from the date 

of purchase), a problem covered by the warranty were 

to arise, SHARK, through the intermediary of its sales 

network, undertakes to repair or replace any defective 

components, up to a maximum limit which is the pur-

chase value of the helmet. Any labour costs are normally 

paid by the SHARK network, but are submitted for appro-

val prior to the work being carried out.

If the repair requires components to be dispatched incur-

ring transportation costs, the SHARK network shall cover 

these costs up to a limit which is the cost of transport by 

the national postal service at the normal rate.

exclusions

This warranty only covers problems related to materials 

or manufacturing. SHARK cannot be held liable with 

regard to the product in the following cases :

Any damage following

1) a fall or accident

2) a technical modification made by the user or a third 

party (glue, adhesives, paint, screws, etc.)

3) use of or contact with: harmful chemical products 

(including methylated spirits on the visor treatments), or 

an intense heat source

4) incorrect use: abnormal conditions (e.g. underwater), 

lack of maintenance or care

5) ageing due to normal wear of the inner fabrics or 

foams, the appearance of the external parts, or the visor 

(scratches, marks, etc.)

6) abnormal and prolonged exposure to ultra- violet 

light, in particular for the decorative colours. In addition, 

SHARK cannot consider subjective considerations related 

to use of the helmet as defects covered by the warranty: 

problems with comfort, size, noise or whistling, aerody-

namics, etc.

SHARK cannot be held liable for the temporary non-avai-

lability of the helmet while it is being

enhanced to satisfy the needs of its owner. In all cases, 

the maximum warranty period is 5 years. Replacement 

of a component during this period does not prolong this 

period.

Procedure

When the helmet is sold go to our website www.shark-

helmets.com in order to activate your warranty. All war-

ranty claims must be made to the SHARK dealer that sold 

the helmet.

For a warranty claim to be considered, the purchaser 

must notify the dealer of the problem that has arisen, and 

return the helmet that is the subject of the claim, together 

with the warranty card filled out when the helmet was 

purchased. This warranty does not affect in any way the 

statutory rights of the purchaser as stipulated by direc-

tive 1999/44CE.

The effects of this specific and limited warranty shall 

come to an end after a period of 5 years as from the 

date of purchase. After this period, if you continue to use 

a helmet regularly, we recommend that to benefit from 

optimum protection and comfort you should replace your 

helmet. This is because certain external factors - general 

wear, certain impacts - could be prejudicial to the safety 

characteristics of this essential piece of protective equip-

ment.

limit

SHARK reserves the right to carry out work within the 

terms of the warranty using replacement parts from the 

most recent version compatible with the model concer-

ned, and is unable to guarantee perfect harmonisation of 

the paint or decorative elements associated with specific 

production runs and/or limited editions. In addition, the 

natural deterioration of colours over a period of time can 

cause mismatching in the adaptation of colours of spare 

parts.

If SHARK is unable to carry out the repair for technical 

reasons or because a component is not available, SHARK 

undertakes to make the customer an advantageous offer, 

taking account of the age of the helmet, consisting in 

either an identical new helmet or an equivalent model 

manufactured at the time of the repair, if the original 

model is no longer available.

WaRRaNty

Summary of Contents for Nano





















Reviews: