manualshive.com logo in svg

SGM X Line IDEA WASH 575, User Manual

Share
Download
SGM X Line IDEA WASH 575 User Manual Download Page 25

GB 

 

SGM Technology for Lighting 

Idea Wash 575 

 

WIT074 V1.0-01NR 

 

23 

CLEANING AND MAINTENANCE 

The following points have to be considered during the inspection: 
1.

 

All screws for installing the devices or parts of the device have to be tightly connected and must not be 
corroded. 

2.

 

There must not be any deformations on the housing, color lenses, fixations and installation spots (ceiling, 
suspension, trussing). 

3.

 

Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances. 

4.

 

The electric power supply cables must not show any damage, material fatigue or sediments.   

 
Further instructions depending on the installation spot and usage have to be adhered by a skilled    installer 
and any safety problems have to be removed. 
 

Note:

 

If the external flexible cable or cord of this device is damaged, it shall be exclusively 

replaced by the manufacturer or his service agent or a similar qualified person in order to avoid 
a hazard. 

 

CAUTION

   

 

Disconnect from mains before starting maintenance 
operation. 

 
We recommend a frequent cleaning of the device. Please use a moist, lint- free cloth. Never use alcohol or 
solvents. 
There are no serviceable parts inside the device except for the lamp. Please refer to then instructions under 
“Installation instructions”. 
Should you need any spare parts, please order genuine parts from your local dealer. 

 

TECHNICAL SPECIFICATIONS 

 

Power supply : 

230V/50HZ 

  Power consumption : 

max. 780W 

 

Lamp :

 

Philips MSR 575/2 

  Packing dimensions :

 

61x53x60cm 

 

Net weight :

 

38,5 KGS 

 

  Gross weight 

: 

46 KGS 

 
Remark :

 errors and omissions for every information given in this manual excepted. All information is 

subject to change without prior notice. 

Summary of Contents for X Line IDEA WASH 575





























Reviews:

No comments

Brands by name

Popular brands

Load more brands