background image

23

D

Giotto spot r

el.1.00

E

F

E

EN

N

I

Appendix

6.0 - COLOR CHANNEL - CH 6-

Giotto Spot 1200 is fitted with an exclusive color generation system comprising 12 frames containing dichroic colour fil-
ters. Color changes are controlled by Channel 6,  allowing to select 24 different colors which, combined with the two
colour conversion filters, produce 72 different tones.  As well as selecting the colour, it's also possible to use some func-
tions with great visual impact, such as running the colourchanger in sync with the music or continuous rotation of all the
colours available at 3 different speeds (rainbow effect). By using the colour channel in combination with the strobe chan-
nel, an "autoshade" effect can be obtained, which blacks out projection for a moment when colours are changed. 

DMX VALUE

CENTRAL VALUE

FUNCTION

0 - 7

3

WHITE

8 - 14

11

PINK

15 - 21

18 

MAGENTA

22 - 28

25

LAVENDER

29 - 35

32 

BLU LIGHT

36 - 42

39

AZURE

42 - 49

46

CYAN

50 - 56

53

YELLOW

57 - 63

60

AMBER

64 - 70

67

FLAME RED

71 - 77 

74 

WOOD

78 - 84

81

PRIMARY RED

85 - 91

88

LIGHT GREEN

92 - 98

95

GREEN AZURE

99 - 105

102

GREEN AMBER

106 - 112

109

YELLOW GREEN

113 - 119

116

GREEN CYAN

120 - 126 

123 

GREEN YELLOW

127 - 133 

130 

DARK RED

134 - 140

137

LIGHT MEDIUM BLUE

141 - 147

144

GREEN

148 - 154

151

MEDIUM BLUE

155 - 161

158

MEDIUM RED

162 - 168

165

ORANGE

169 - 175

172

DARK PURPLE

176 - 182

179

RAINBOW SPEED 1 SLOW

186 - 189

186

RAINBOW SPEED 2

190 - 196

193

RAINBOW SPEED  3

197 - 203

200

RAINBOW SPEED 4 FAST

204 - 210

207

MUSIC CHANGE AT EACH BASS BEAT

211 - 217

214

MUSIC CHANGE EVERY TWO 2 BASS BEATS

218 - 224

221

MUSIC CHANGE EVERY 3 BASS BEATS

225 - 255

236

MUSIC CHANGE EVERY 4 BASS BEATS

Summary of Contents for Giotto spot 1200































Reviews: