background image

12

Giotto spot r

el.1.00

2.0-Construction of the signal cable 

Giotto 1200  has a DMX 512 input fitted with standard 5-pin XLR connectors. Screened cables in compliance with EIA RS-
485 specifications and the following characteristics must be used for connections:

- 2 conductors plus screen
- 120Ohm impedance 
- low capacitance
- max. transmission rate 250kBaud.

Cable connections:

see illustration, taking care with the screen, which must be connected
to Pin 1

ATTENTION: the screened parts of the cable (sleeve) must NEVER be connected to the system's
earth, as this would cause faulty fixture and controller operation.

Example of connection of the DMX line 

To avoid the risk of faulty operation, follow these indications:

Maximum cable length:

500 metres

Max. N° of fixtures connected:

32

Cable runs:

Avoid running cables alongside power supply lines.

Termination:

A 120Ohm resistor between Pins 2 and 3 on the last fixture.

2.1- Construction of the DMX termination 

The termination avoids the risk of DMX 512 signals being reflected back along the cable when they reaches the end of

the line: under certain conditions and with certain cable lengths, this could cause them to cancel the original signals.
The termination is prepared by soldering a 120Ohm 1/4 W resistor between pins 2 and 3 of the 5-pin male XLR connector
(see diagram).

1

2

3

4

5

120

in/out dmx

control

gain

GIOTTO REL. 1.00

mic

main power

fuses

Giotto

m o v i n g   h e a d   w a s h   l u m i n a i r e

1200

enter

up

down

down

up

enter

in/out dmx

control

gain

GIOTTO REL. 1.00

mic

main power

fuses

Giotto

m o v i n g   h e a d   w a s h   l u m i n a i r e

1200

enter

up

down

down

up

enter

in/out dmx

control

gain

GIOTTO REL. 1.00

mic

main power

fuses

Giotto

m o v i n g   h e a d   w a s h   l u m i n a i r e

1200

enter

up

down

down

up

enter

Pilot

1 or 21

2 or 22

3 or 23

4 or 24

5 or 25

6 or 26

7 or 27

8 or 28

9 or 29

10 or 30

11 or 31

12 or 32

13 or 33

14 or 34

15 or 35

16 or 36

17 or 37

18 or 38

19 or 39

20 or 40

program

chase

psycho

preset

unit

step

page

store

edit

levels

times

copy

enter

play

extra

lamp

reset

smpte

rec

on/off

u n i v e r s a l   d m x   c o n t r o l l e r

0

10

20

30

40

50

60

70

80

90

100%

2000

2000

programming keyboard

multifunction keyboard

grand master

operations

utility

memory obj

memory

1 - 20

21 - 40

setup

Termination DMX

(last ap)

DMX controller

DMX linea

pan

tilt

D I M M R
      0

C O L O R
      0

G O B O S
      0

S H U T T
      0

R O T G B
      0

F R O S T
      0

-     0
-     0

1

2

3

4

5

COMMON
DMX-
DMX+

Summary of Contents for Giotto spot 1200































Reviews: