SEW-Eurodrive MOVIFIT-FC Operating Instructions Manual Download Page 101

Page: 101 / 172

Startup

Startup MOVIFIT®

Operating Instructions – MOVIFIT

-FC

101

4. To start up the MOVIFIT

frequency inverter, see the section "Startup MOVIFIT

Frequency Inverter" (see page 104).

5. Mount the MOVIFIT

-EBOX on the ABOX and close it.

6. Switch on the 24V_C and 24V_S supply voltage(s). The associated control LEDs

should now light up green.

Bus termination

The bus terminating resistors are already installed in the MOVIFIT

-ABOX (only with

standard ABOX "MTA...-S02.-...-00" and hybrid ABOX "MTA...-S42.-...-00") and can be
activated using switch S1, see section "ABOX" (see page 14):

The following table shows the operating principle of the bus termination switch:

Bus termination ON = on

Bus termination OFF = off

(factory setting)

837515659

837519755

Bus termination switch S1

Bus termination ON = on

Bus termination OFF = off

837562251

837566347

OFF

Bus

termination

Incoming

cable

Outgoing

cable

Switch

OFF

Bus

termination

Incoming

cable

Outgoing

cable

Switch

TIP

When using the following connection boxes, please note:
• Hybrid ABOX "MTA...-S52.-...-00"
• Han-Modular

-ABOX "MTA...-H12.-...-00"

In contrast to the standard ABOX, these connection boxes require a plug-in bus termi-
nator (M12) at the last station instead of the outgoing bus connection.

Summary of Contents for MOVIFIT-FC













































































































































































Search results

Summary of Contents for MOVIFIT-FC

Reviews:

SEW-Eurodrive MOVIFIT-FC, Operating Instructions Manual, Page: 101 / 172

Search results

Summary of Contents for MOVIFIT-FC

Reviews: