SEW-Eurodrive MOVIDRIVE MDR60A1320-503-01 Operating Instructions Manual Download Page 4

1

General information

About this documentation

Addendum to the Operating Instructions – MOVIDRIVE

®

 MDR60A1320-503-01 regenerative power supply

4

1

General information

1.1

About this documentation

The documentation at hand is the original.

This documentation is an integral part of the product. The documentation is intended
for all employees who perform work on the product.

Make sure this documentation is accessible and legible. Ensure that persons respon-
sible for the systems and their operation as well as persons who work on the product
independently have read through the documentation carefully and understood it. If you
are unclear about any of the information in this documentation or if you require further
information, contact SEW‑EURODRIVE.

1.2

Structure of the safety notes

1.2.1

Meaning of signal words

The  following  table  shows  the  grading  and  meaning  of  the  signal  words  for  safety
notes.

Signal word

Meaning

Consequences if disregarded

 

DANGER

Imminent hazard

Severe or fatal injuries

 

WARNING

Possible dangerous situation

Severe or fatal injuries

 

CAUTION

Possible dangerous situation

Minor injuries

NOTICE

Possible damage to property

Damage to the product or its envi-
ronment

INFORMATION

Useful information or tip: Simplifies
handling of the product.

1.2.2

Structure of section-related safety notes

Section-related  safety  notes  do  not  apply  to  a  specific  action  but  to  several  actions
pertaining to one subject. The hazard symbols used either indicate a general hazard
or a specific hazard.

This is the formal structure of a safety note for a specific section:

SIGNAL WORD

Type and source of hazard.

Possible consequence(s) if disregarded.

Measure(s) to prevent the hazard.

27789314/EN – 07/2022

Summary of Contents for MOVIDRIVE MDR60A1320-503-01

































Reviews: