Safe Warnings and
Important Information
• DO NOT store delicate items directly in your safe.
–
In order to protect your valuables from potential threats of
flood, your safe is equipped with an airtight gasket. Because
of this gasket, moisture in the air could potentially be locked
inside your safe and accumulate inside your safe.
–
The desiccant bag included in your safe during shipment
should be left inside your safe. DO NOT DISCARD IT. It is
intended to help absorb moisture. Replace or recharge
your desiccant bag every 6 months or as needed for
optimum performance.
–
If you choose to store delicate items such as jewelry with
working parts, watches, stamps or photos in your safe, we
recommend putting them in an air-tight container prior to
placing in the safe for storage.
–
NOTE: SentrySafe will not be responsible for any damage or
loss of items placed in the unit due to moisture.
• DO NOT store pearls in this safe.
In the event of a fire, the interior
of your safe may reach up to 350˚F. While this temperature is
safe for your paper documents, digital media and other valuables,
pearls can be damaged at much lower temperatures.
• DO NOT store any film based technology or media in
this safe.
–
This product is not intended to protect computer floppy disks
or diskettes, film cartridges, tapes, audio/video cassettes or
photo negatives.
• Your safe is only part of your total security protection.
–
SentrySafe recommends that you store your safe in closets,
offices, basements, bedrooms and any other locations that
are convenient for you but out of direct line of sight from
prying eyes. The location of the safe does not affect the
safe’s ability to protect your valuables inside.
• This product is not intended for the secure
storage of all materials.
Items such as
firearms, other weapons, combustible
materials and medication should not be stored
in this unit.
If your SentrySafe product is in a fire, it will be sealed shut making it necessary for it to be pried open. To help your family begin again, SentrySafe will ship a replacement
free of charge. To be eligible for the Limited Lifetime After Fire Replacement Program, you (the original owner) must register your product using the included registration form
or by visiting
www.registermysafe.com.
For more information about the Limited Lifetime After-Fire Replacement Program, visit
SentrySafe.com
Limited Lifetime After-Fire Replacement Program
To Add a Secondary Fingerprint User
1
2
Press: “
P
”
Enter your programmed 5 digit primary user code.
NOTE:
Blue light will blink to indicate the fingerprint sensor is
ready to scan a new fingerprint.
Swipe the first finger 5-10 times. Between each finger swipe
you should hear a single beep to indicate the fingerprint
was scanned.
When the safe has registered the first fingerprint the green
indicator light will blink 3 times and you will hear 3 beeps.
To register a second fingerprint for this user – immediately
repeat steps 3 & 4 with a second finger for this user.
-OR-
If you would like to program only one finger press “
C
”.
3
4
5
Deleting a Secondary Fingerprint User
1
2
Press: “
P
”
Enter your programmed 5 digit primary user code.
Swipe any fingerprint once.
Press: “
C
”
NOTE:
The electronic lock will NOT indicate that it has
deleted the user’s fingerprint—please test to make sure it has
been deleted.
NOTE:
This will delete both fingerprints for this user.
3
4
NOTE:
Delay mode will occur if 5 consecutive invalid entries have
been tried. The red LED will blink on and off to let you know the safe
is in delay mode. This will cause the system to shutdown for two
minutes. DO NOT remove the batteries to restart the system; it will
only increase the length of time for the system shutdown.
1
2
Press: “
C
” or touch the fingerprint
sensor until indicator light is blue
to awaken the safe.
Swipe you finger in the
downward direction over the
fingerprint sensor. A green
light and one beep indicate
your finger has been scanned.
Rotate the handle downward
to open the door
3
Programming Safe Features
To turn the light feature
off
: Press: “
0
” – “
P
” – “
2
”
To program the light
on
for 30 seconds: Press: “
0
” – “
P
” – “
3
”
To program the light
on
for 60 seconds: Press: “
0
” – “
P
” – “
4
”
Digital Keypad Sound On/Off
To turn keypad sound
off
: Press: “
0
” – “
P
” – “
0
”
To turn keypad sound
on
: Press: “
0
” – “
P
” – “
1
”
Unlocking the Safe
Using the
Fingerprint Scanner
Interior Light
The interior light in your safe can be programmed to illuminate for
various time intervals upon opening your safe.
NOTE:
Turning the keypad sound off may make it more difficult to use
fingerprint scanner as a single beep indicates your finger has been
scanned.
English
