Sentry The Guardimals Owner'S Manual Download

Page: 75 / 94

The harness system on this Car Seat has an adjuster allowing

1. Tighten the harness straps to snugly

adjust harness around child by pulling the
Harness Adjuster Strap at the front of the
Car Seat as shown.

2. Make sure the straps are ﬂat and snug

against the child’s shoulders and thighs.
NOTE: A snug strap should not allow any
slack. It lies in a relatively straight line
without sagging. It does not press on the
child’s ﬂesh or push the child’s body into
an unnatural position.

WARNING!

• To prevent injury from contact with the vehicle interior or

ej ection, the harness system must be snugly adjusted
ar ound child.

Changing

Harness

Strap

Adjustment

tighten

harness

strap

adjustment of harness strap for a snug ﬁt on your child.

10.0 Operation and Adjustements

Summary of Contents for The Guardimals































































































Search results

Summary of Contents for The Guardimals

Reviews:

Related manuals for The Guardimals

Brands by name

Popular brands

Sentry The Guardimals, Owner'S Manual

Search results

Summary of Contents for The Guardimals

Reviews:

Related manuals for The Guardimals

Brands by name

Popular brands