background image

Transducer Control 5 User Manual (RWT3746IM) 

Revision 7, September 2020 - Page 27 

Zero Offset 

The Zero Offset feature sets a fixed torque offset value. The Zero Offset can be used 
to remove any offset that may have been introduced from its mechanical installation, 
or from idle torque present. It must be stressed that the zero offset is no substitute for 
correct installation. 
 
Any torque value up to FSD is permitted; values over 25% of FSD are allowed but are 
not advisable. Using an offset of over 25% will flag the High Zero Offset warning. When 
using high zero offsets, care must be taken not to overstrain the transducer. A zero 
offset  will  not  extend  the  full-scale rating  of  the  transducer,  e.g.  if  a  transducer  was 
zeroed at 50% then a further 50% was applied, the transducer will have reached full 
scale, even though the transducer would be reading 50%. 
 
The  zero  offset  can  be  temporarily  overridden  by the  digital  zero  commands,  or the 
Normal/Average Zero Input. When the transducer is power cycled the saved zero offset 
will be restored. 
 
The offset can be entered manually or set from one of 3 options. 
   
 

 

 
 

Offset Torque Value 

The 

“Offset Torque Value” text box is the torque offset value in the transducer’s native 

unit. The offset is subtracted from the captured torque readings. Manually type in the 
required offset, or select from the 3 options. 
 

Current Zero 

The 

“Current Zero” button sets the “Offset Torque Value” to the current zero 

offset value of the transducer. 
 

Clear Offset 

The 

“Clear Offset” button sets the “Offset Torque Value” to zero. 

 

Load Applied 

The 

“Load  Applied”  button  sets  the  “Offset  Torque  Value”  to  the  current  un-

zeroed torque value. 

 

Save Zero Offset 

The 

“Save Zero Offset” button saves the “Offset Torque Value” into the transducer’s 

memory.  The  offset  will  be  retained  across  power  cycles,  until  it  is  cleared  by  this 
setting, by the zero input on the transducer, or a factory reset. 

Summary of Contents for RWT440
















































































Reviews: