Sensor Technology RWT440 User Manual Download

Page: 36 / 79

Transducer Control 5 User Manual (RWT3746IM)

Revision 7, September 2020 - Page 4

Transducer Requirements

•

Advanced ORT/RWT Series Transducer.

•

RS232 or USB connection to a PC, or an Ethernet Module and network connected

PC.

PC Requirements

Operating System:

Microsoft Windows 7/8/8.1/10 32/64bit.

CPU:

Intel or AMD 1GHz.

RAM:

512MB.

Hard Drive Space:

4MB + 2GB for Microsoft .NET Framework 4 Runtime.

Installation

Transducer Control can be installed from a supplied CD, USB Flash Drive or
downloaded from our web site.

CD/USB Flash Drive

To install Transducer Control 5 from a CD or USB Flash Drive:

1. Insert the Sensor Technology Installation CD into your CD-ROM drive, or plugin

the USB flash drive.

If the install loader doesn’t run, use Windows Explorer to

navigate to the CD-ROM or flash drive, then run autorun.exe. The following
screen will be displayed.

2. Click the

“Install” button next to “Transducer Control 5”.

3. Follow the onscreen instructions.
4. Transducer Control will now be installed and be ready for use.

The USB drivers are installed as part of the installation.

Web Site Download

To install Transducer Control 5 from our web site:

1. Go to our software downloads page and download Transducer Control:

https://www.sensors.co.uk/torque-sensors/torqview/software-downloads/

2.  Open the downloaded Zip file and run setup.exe.
3.  Follow the onscreen instructions.
4.  Transducer Control will now be installed and be ready for use.

The USB drivers are installed as part of the installation.

Summary of Contents for RWT440
















































































Search results

Summary of Contents for RWT440

Reviews:

Related manuals for RWT440

Brands by name

Popular brands

Sensor Technology RWT440, User Manual

Search results

Summary of Contents for RWT440

Reviews:

Related manuals for RWT440

Brands by name

Popular brands