Sensor Technology RWT440 User Manual Download

Page: 22 / 79



Sensor Technology 2016

Page 21

RWT3745V (Rev 2)

Declaration of Conformity

EC Directives

We, Sensor Technology Ltd, hereby declare that the products named below, to which this

Declaration of Conformity relates, is in conformity to the requirements of EC Council

Directives and Standards as listed:

▪

2004/108/EC (Electromagnetic compatibility).

▪

BS EN 61326-1:2006, (Electrical equipment for measurement, control and laboratory

use).

Type of Product

Rotary Torque Transducer

Product Name(s)

RWT410, RWT411, RWT413.

RWT420, RWT421.

RWT430, RWT431, RWT433,

RWT440, RWT441, RWT442.

Intended use:

Measurement of rotary torque within the rated torque

and speed limits as described on the transducer.

……………………….......................................

Managing Director

Sensor Technology Ltd

November 2016

Apollo Park, Ironstone Lane, Wroxton, Banbury

Oxon, OX15 6AY

Tel: +44 (0)1869 238400 Fax: +44 (0)1869 238401

Email: [email protected] Web: www.sensors.co.uk

Summary of Contents for RWT440
















































































Search results

Summary of Contents for RWT440

Reviews:

Related manuals for RWT440

Brands by name

Popular brands

Sensor Technology RWT440, User Manual

Search results

Summary of Contents for RWT440

Reviews:

Related manuals for RWT440

Brands by name

Popular brands