manualshive.com logo in svg

Sensor Technology RWT440, User Manual

Share
Download
Sensor Technology RWT440 User Manual Download Page 2

 Sensor Technology 2016

 

Page 1

 

RWT3745V (Rev 2)

 

 
 
 
 
While every precaution has been exercised in the compilation of this document to ensure the 
accuracy of its contents, Sensor Technology Ltd, assumes no responsibility for any errors or 
omissions. Additionally, no liability is assumed for any damages that may result from the use 
of the information contained in this document. 
 

Patents 

Sensor Technology Ltd’s RWT series products are manufactured under one of the following 
US patents: 5,585,571; 6,237,417; 6,467,351; 6,765,493; 6,838,958; 6,864,759. 
 

Copyright 

Copyright 

2016 Sensor Technology Ltd.  All rights Reserved. 

Copying  or  reproducing  of  all  or  any  part  of the  contents  of this manual  is  strictly  prohibited 
without the express permission of Sensor Technology. 
 

Trademarks 

TorqSense

 is a registered trademark of Sensor Technology Ltd. 

TorqView

 is a trademark of Sensor Technology Ltd. 

LabVIEW

 is a trademark of National Instruments Corporation. 

National Instruments

 is a trademark of National Instruments Corporation. 

Windows

 is a registered trademark of Microsoft Corporation. 

 
Lifetime Warranty 

Sensor  Technology  Ltd’s  standard  range  of  products  are  warranted  against  manufacturing 
defects and component failure for two years from date of purchase, subject to fair wear and 
tear  and  return  for  the  first  year's  free  of  charge  annual  re-calibration.  This  warranty  is 
extended indefinitely if the equipment is returned to Sensor Technology, or its distributor, for 
annual  re-calibration,  when  software  and  hardware  updates,  if  required,  will  be  carried  out 
free of charge. Standard range means those products as described in the company's product 
data sheets. 

 

 

Summary of Contents for RWT440
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands