background image

MODULE LAYOUT

PRELIMINARY WARNINGS

The word 

WARNING

 preceded by the symbol 

 indicates conditions or actions that put the user's safety at 

risk. The word 

ATTENTION

 preceded by the symbol 

  indicates conditions or actions that might damage the 

instrument or the connected equipment. The warranty shall become null and void in the event of improper use or 

tampering with the module or devices supplied by the manufacturer as necessary for its correct operation, and if 

the instructions contained in this manual are not followed.

WARNING

: The full content of this manual must be read before any operation. The module must only be used by 

qualified electricians. Specific documentation is available at www.seneca.it/products/z-key-wifi

Important: Obstructing ventilation slots with any object is prohibited. 

Installing the module next to devices that generate heat is prohibited.

Electrical and electronic waste disposal (applicable in the European Union and other countries with recycling).

The symbol on the product or its packaging shows the product must be surrendered to a collection centre 

authorized to recycle electrical and electronic waste.

The module must be repaired and damaged parts replaced by the Manufacturer. The product is sensitive to 

electrostatic discharges. Take appropriate measures during any operation.

LED

STATUS

LED meaning

PWR Green

ON

The device is powered correctly

SD Red

Flashing

Accessing the microSD card

TX1 Red

Flashing

Data transmission on port #1 RS485

RX1 Red

Flashing

Data receipt on port #1 RS485

TX2 Red

Flashing

Data transmission on port #2 RS485/RS232

RX2 Red

Flashing

Data reception on port #2 RS485/RS232

ETH ACT Green

Flashing

Packet transmission on Ethernet port

ETH ACT Green

ON

No activity on Ethernet port

ETH LNK Yellow

ON

Ethernet connection present

ETH LNK Yellow

Off

No Ethernet connection

4 LED

On

Signal strength (0 = min. / 4 = max.)

AP

On

Access Point mode active

AP

Flashing

Access Point mode first configuration

ST

On

Station mode active

SIGNALS VIA LED ON FRONT PANEL

2/8

m

m

35

  

mm

111

  

mm

102.5

Dimensions:

 LxHxD 35 x 102.5 x 111; 

Weight:

: 220 g; 

Enclosure:

 PA6, Black

Summary of Contents for Z-KEY-WIFI









Reviews: