background image

 

User Manual

 

T201DCH50/100/300/600-MU 

 

 

ALL RIGHTS RESERVED. NO PART OF THIS PUBLICATION MAY 

BE REPRODUCED WITHOUT PRIOR PERMISSION.

 

www.seneca.it

 

Doc. MI00546-EN

 

Rev.2 

Page 10 

 

 
 

WARNING!

 

You can Write a Maximum of 2 Modbus Registers with the Write Multiple Register function (function 

16)

 

 
 

WARNING!

 

The USB Modbus configuration is fixed to 38400 baud, 8bit , No parity, 1 stop bit 

When the USB cable is inserted the RS485 will stop to communicate until the USB will be unplugged. 

 

 

MODBUS REGISTER TABLE 

5.

 

The following abbreviations are used in the register tables: 

 
MS = More significant 
LS = Less significant 
MSW = 16 most significant bits 

LSW = 16 least significant bits 
MSW* = 16 most significant or least significant bits depending on the configuration (most significant default) 

LSW* = 16 less significant or more significant bits depending on the configuration (less significant default) 
MSW = 8 most significant bits 

LSW = 8 least significant bits 
MSBIT = Most significant bit 
MSBIT = Least significant bit 

RO = Register in read-only 
RW = Read/write register 

RW** = Reading and writing register contained in flash memory, writable a maximum of 10000 times. 
Unsigned 16 bit = unsigned integer register, can take values from 0 to 65535 

Signed 16 bit = signed integer register can take values from -32768 to +32767 
Float 32 bits = 32-bit single-precision floating point register (IEEE 754) 

https://en.wikipedia.org/wiki/IEEE_754 

BIT = Boolean registry, can be 0 (false) or 1 (true) 

 

 

 

Summary of Contents for T201DCH100-MU



























Reviews: