background image

Model SSD1-HS 

508.366.1488 | semshred.com                                                          Page 2

 of 23

 

1 - Safety Considerations

 

ü

 

Read and understand instruction manual and be aware of all warning labels. 

 

ü

 

Always 

employ proper Lock Out Tag Out (LOTO) procedures when shredder is not in 

use, when servicing shredder or when performing routine shredder maintenance 

including cleaning. 

 

ü

 

Make sure that all guards and access panels are in place at all times, unless

 

the power is 

locked off for maintenance work or cleaning. 

 

ü

 

SEM recommends that machine operators wear safety glasses, hearing protection, a 
mask, and if doing maintenance or opening the cutting chamber, cut resistant gloves. It 
is up to each customer to determine the PPE for their individual site.  

 

ü

 

Always 

know where the emergency stop buttons are located. 

 

ü

 

Always 

know or have quick access to emergency phone numbers. 

 

ü

 

Always 

ensure that all maintenance and operating personnel read and understand this 

manual, including those personnel working second or third shift. 

 

ü

 

Always 

have a standard break-in time for a new operator. A minimum of two hours is 

suggested. 

 

ü

 

Always 

wear safety glasses when operating shredder. 

 

ü

 

Never 

operate this or any other machine while under the influence of drugs, alcohol, or 

medications. 

 

ü

 

Never 

wear loose fitting clothing, ties, or jewelry while in the vicinity of this shredder. 

 

ü

 

Never 

allow long hair in the vicinity of the machine without use of a protective hair net. 

 

ü

 

Never 

place any part of your body in or on any part of the machine while in operation. 

 

ü

 

Neve

r allow other personnel within ten feet of this machine while in operation. 

 

ü

 

Never 

remove guards, perform maintenance, or clear jammed debris without first 

locking out power disconnect.

 

 

ü

 

Never 

allow horse play around machine.

 

Summary of Contents for SSD1-HS

























Reviews: