SelectBlinds Fashion Color Power Touch Series Page 27 Installation & Care Instructions Download | Manualshive

Page: 27 / 31

background image

18

REPLACING THE BATTERY IN THE REMOTE

TIMER REMOTE

Slide the back of the remote down and then lift off the back cover.

Insert the new battery (CR2450 lithium) into the battery compartment so that

the writing is facing up (positive up) when the remote is face down.

Replace the back cover on the remote.

Insert fingernail here

LITHIUM BATTERY

CR2430 3V

CR2450

OPEN

Standard Remote

Timer Remote

STANDARD REMOTE

Remove the battery tray from the remote by inserting a fingernail into the

indentation on the back of the remote. To avoid the battery falling out of the

remote, remove the tray while the remote is face up.

Insert the new battery (CR2430 lithium) into the battery tray so that the writing

is facing up (positive up) when the remote is face up. Slide the tray back into the

remote.

«
...
25
26
27
28
29
...
»

Summary of Contents for Fashion Color Power Touch Series
































Reviews:

No comments

Related manuals for Fashion Color Power Touch Series

Brand: YewdaleDefiant Pages: 8

Brand: Home Decor Pages: 4

VL31 Split Draw

Brand: YewdaleDefiant Pages: 8

Wood Line Series

Brand: Swiss Sonnenschutz Pages: 4

Roller Blind Duo

Brand: Victoria M Pages: 4

Plissee nach mass

Brand: Victoria M Pages: 7

Brand: Victoria M Pages: 16

Smart Day & Night

Brand: Diaz Pages: 6

Brand: livani Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands