SelectBlinds Fashion Color Power Touch Series Page 22 Installation & Care Instructions Download

Page: 22 / 31

PROGRAMMING TIMER REMOTE

SETTING CLOCK

Use the power button to turn on the remote.

Tap the

CLOCK

button until you see

“MANUAL” in the display.

Push and hold the

LIMIT

button. While

holding the

LIMIT

button, push the

CLOCK

button for 3 seconds and release.

The hour digits will flash.

Use the

and

DOWN

buttons to set the

current hour.

NOTE:

Time is in 24 hour

format (military time). For example: 1:00

PM will be displayed as 13:00.

Press

CHANNEL

button to confirm hour

and advance to minutes.

06:42

MANUAL

Power

Button

Stop/Favorite

Down

Channel

Clock

Confirm Limit

Timer Remote

Display

Screen

FF:FF

Auto

STOP

Channel

= Select

= Confirm

Use the

and

DOWN

buttons to set the current minute.

Press

CHANNEL

button to confirm minute and advance to day.

Use the

and

DOWN

buttons to set the current day.

Hold the

CLOCK

button for 3 seconds. Display will flash and then display the

current time and day.

Summary of Contents for Fashion Color Power Touch Series
































Search results

Summary of Contents for Fashion Color Power Touch Series

Reviews:

Related manuals for Fashion Color Power Touch Series

Brands by name

Popular brands

SelectBlinds Fashion Color Power Touch Series, Installation & Care Instructions

Search results

Summary of Contents for Fashion Color Power Touch Series

Reviews:

Related manuals for Fashion Color Power Touch Series

Brands by name

Popular brands