manualshive.com logo in svg

Seip TM 50, Installation And Programming Instructions

Share
Download
Seip TM 50 Installation And Programming Instructions Download Page 2

Installation Instructions TM50/TM80 - MO911/1V0

Page 2

Content

Quick Reference for experienced Installers    ���������������������3

Information and Remarks

Regulations and Usage    ��������������������������������������������������4

Directives and Regulations
Use of the operators
Garage Doors
The installers declaration of conformity
Older Garage Doors
Instruction for the users

Safety Advises for the Installation    ����������������������������������5

Installation

Conditions for Installation    ����������������������������������������������6

Minimum Headroom
Door Hight
Door Arm Extension
Dimensions

Pre-Mounting    ����������������������������������������������������������������6

Installation    ���������������������������������������������������������������������7

Installation

Adjusting the Limit Blocks    ����������������������������������������������8

The Emergency Release    �������������������������������������������������9

When the garage door is the only entrance
When there is a second entrance to the garage

Printed Circuit Board: Adjustments and Connectors

Control Elements    ���������������������������������������������������������10

Connectors    ������������������������������������������������������������������11

Push Button
Photo Cell / Hatch Door Contact

Printed Circuit Board: Adjustments and Connectors

Standard Programming    ������������������������������������������������12

Programming Forces and Running Distance
Choosing the type of door
Programming Remote Components

Free Programming    �������������������������������������������������������13

Setting the speeds
Setting the opening speed
Changing the length of Soft Stop

Automatic Closing    �������������������������������������������������������14

Setting the time
Pre-Warning by internal lighting
Connecting a Photo-Cell
Performance of Control Devices
Avoiding automatic closing temporarily
Further Safety Advice for Automatic Closing

Adjusting the Lighting Duration    �����������������������������������15

Remote Control

Registering and deleting Remote Devices    ���������������������������������16

Starting the Registry
Registering a Device
HomeLink™
Erasing Remote Devices

General Remarks    ���������������������������������������������������������������������17

Useable Batteries
Changing the transmitters‘ battery
Changing the wall push-buttons‘ battery
Synchronisation of the Rolling Code

Technical Information

Technical Data    �������������������������������������������������������������������������18

Wiring Diagram    �����������������������������������������������������������������������18

Internal Wiring
External connections 
Devices for adjustments
Others

Troubleshooting    �����������������������������������������������������������������������19

Error Messages
Messages by blinking integrated lighting
Additional messages from the LED „Diag“ only
If... then...

Declarations

EC-Declaration of Conformity    ��������������������������������������������������20

www.thegaragedoorcentre.co.uk

0800 525 442

www.thegaragedoorcentre.co.uk

www.thegaragedoorcentre.co.uk

0800 525 442

www.thegaragedoorcentre.co.uk

Summary of Contents for TM 50





















Reviews:

No comments

Brands by name

Popular brands

Load more brands