manualshive.com logo in svg

Seip TM 50, Installation And Programming Instructions

Share
Download
Seip TM 50 Installation And Programming Instructions Download Page 12

Installation Instructions TM50/TM80 - MO911/1V0

Page 12

Programming the Forces and Running Distance

1

Choosing the type of door

The standard pre-setting is „Sectional Door“; if this shall be used, then proceede with step 2�
For other types of doors the DIP-switches 1 and 2 must be adjusted accordingly�

Sectional Door

Tilting Door

Short Running Door

Short Running Door

Free Programming

When the DIP-switch settings are changed, the red LED starts blinking in intervalls; proceede 
as described below�

Pls� refer to chapter „Free 
Programming“, Page 13�

2

Keep the red LEARN-button pressed for approx� 3 seconds�
Release the button once the red LED and the operators‘ lighting start blinking�

3

Press the LEARN-button once again shortly�

4

The operator now starts with the learning cycles (force measurement and running distance):
- it hits the OPENING limit block
- it closes slowly until it reaches CLOSED-position
- it opens fast until it reaches OPEN-position
- it closes fast until it reaches CLOSED-position
The operators‘ light keeps blinking for a little while after the operator stops running� Once 
the operators‘ light stops blinking the programming has been successful�

Programming Remote Components

1

Keep the red LEARN-button pressed for approx� 3 seconds�
Release the button once the red LED and the operators‘ lighting start blinking�

2

Press the button on the remote component which is intended for use with the operator for approx� 1 second� The opera-
tors‘ light stops blinking and the component was programmed successfully�
Steps 1 and 2 must be repeated for each remote component�
For more information on remote components pls� refer to page 16�

Printed Circuit Board: Adjustments and Connectors

Standard Programming

www.thegaragedoorcentre.co.uk

0800 525 442

www.thegaragedoorcentre.co.uk

www.thegaragedoorcentre.co.uk

0800 525 442

www.thegaragedoorcentre.co.uk

Summary of Contents for TM 50





















Reviews:

No comments

Brands by name

Popular brands

Load more brands