Seiko Astron 3X22 Complete User Manual Download

Page: 13 / 50

This is a list of time differences around the world.
When performing manual time difference setting (selection), refer to the crown rotation direction.

DST (Daylight Saving Time) has been adopted in countries marked with a

In the Lord Howe Island time zone in Australia with a

mark, the time is advanced by 30 minutes while DST (Daylight Saving Time) is in effect.

Representative city names…

All global time zones

Time difference from UTC:

+14 hours ~ –12 hours

→ Time zone adjustment

P. 19

→ How to perform manual time difference setting (selection)

P. 23

Operation of the crown when manually setting the time

difference

Turning the crown to the

right moves the time

forward.

Turning the crown to the left

moves the time backward.

City name

UTC ± hours

London

Paris/

Berlin

Cairo

Jeddah

Tehran

+3.5

Dubai

Kabul

+4.5

Karachi

Delhi

+5.5

Kathmandu

+5.75

Dhaka

Yangon

+6.5

Bangkok

Beijing

Eucla

+8.75

Tokyo

Adelaide

+9.5

Sydney

+10

Lord Howe Island

+10.5

City name

UTC ± hours

Nouméa

+11

Wellington

+12

Chatham Islands

+12.75

Nuku’alofa

+13

Kiritimati

+14

Baker Island

-12

Midway islands

-11

Honolulu

-10

Marquesas Islands

-9.5

Anchorage

-9

Los Angeles

-8

Denver

-7

Chicago

-6

New York

-5

Santo Domingo

-4

St. John’s

-3.5

Rio de Janeiro

-3

Fernando de Noronha

-2

Azores

-1

* Information about time differences among regions (time zones) and the

implementation of DST (daylight saving time or “summer time”) is as of

January 2019.

List of time differences around the world (for reference)

BEFORE USE

ASTRON 3X22 GPS SOLAR

Summary of Contents for Astron 3X22



















































Search results

Summary of Contents for Astron 3X22

Reviews:

Related manuals for Astron 3X22

Brands by name

Popular brands

Seiko Astron 3X22, Complete User Manual

Search results

Summary of Contents for Astron 3X22

Reviews:

Related manuals for Astron 3X22

Brands by name

Popular brands