manualshive.com logo in svg

Seiko Astron 3X22, Complete User Manual, Page: 6 / 50

Share
Download
Seiko Astron 3X22 Complete User Manual Download Page 6

Mechanism by which the GPS solar watch sets time and date

GPS satellite

This is a satellite operated by the United States Department of

Defense (official name is NAVSTAR), and orbits the earth at an

altitude of 20,000 km.
Initially, this was a military satellite, but at present, information

is partially disclosed to the public and used in various equipment

including car navigation systems and cellular phones.
The GPS satellite is mounted with a high-accuracy atomic clock

with an accuracy deviation of 1 second per 100,000 years.

Mechanism by which this watch sets the time and date

This watch receives GPS signals from GPS satellites to set the

time and date based on the following information.

•

Precise time and date based on the atomic clock

•

Time zone information for your current location

(The current location is generally measured using 4 or more

GPS satellites, to identify where among the world’s time

zones the watch is located.)

 * To receive information about a time zone where you are, it is necessary

to adjust the time zone.

→ How to adjust the time zone

　

P. 20

 * Unlike navigation equipment, this GPS solar watch is not designed to

constantly receive GPS signals from GPS satellites without any

operation.

This watch receives GPS signals only in the time zone adjustment mode,

automatic or manual time adjustment mode.

5

1

READ FIRST

ASTRON 3X22 GPS SOLAR

Summary of Contents for Astron 3X22



















































Reviews:

No comments