Seiko Precision BX-900 Owner'S Manual Download Page 20

Page: 20 / 146

Connecting the computer

The printer has a parallel interface connector (Centronics) and a serial interface connector (RS232C).

Before you connect an interface cable to your computer, you need to know what type of printer

driver is supported by your software applications and what type of connector is needed to attach the

printer to the computer.

❏

Parallel Interface
36-pin plug

❏

Serial Interface
25-pin plug

Connecting the power cord

Check the power requirement printed on the rating plate on the rear of the printer before attaching

the power cord and turning on the printer. Both POWER and P.OUT lamps light up when the

printer is switched on correctly. The voltage selector should be set correctly as follows.

CAUTION

220-240V

120V

CAUTION

220-240V

120V

T5A 250V

T2.5A 250V(For European)

CAUTION

220-240V

120V

Voltage Selector

2. Setting up

120V : USA, Canada

230V : Europe, Asia, Oceania

Note

For continued protection against risk of fire and
destruction of Power PCB Assembly, switch the
voltage selector according to using voltage.

Summary of Contents for BX-900



















































































































































Search results

Summary of Contents for BX-900

Reviews:

Related manuals for BX-900

Brands by name

Popular brands

Seiko Precision BX-900, Owner'S Manual

Search results

Summary of Contents for BX-900

Reviews:

Related manuals for BX-900

Brands by name

Popular brands