Sega MISSION IMPOSSIBLE ARCADE Owner'S Service Manual Download Page 6

Page: 6 / 167

INTRODUCTION

Parts replacement, maintenance inspections and troubleshooting should be carried out by site maintenance personnel

or other qualified professionals. This manual includes directions for potentially dangerous procedures which should

only be carried out by professionals with the appropriate specialised knowledge.

The site maintenance personnel or other qualified professionals mentioned in this manual are defined as follows:

Site maintenance personnel:

Individuals with experience in maintaining amusement equipment, vending machines, etc., working under the super-

vision of the owner/operator of this product to maintain machines within amusement facilities or similar premises by

carrying out everyday procedures such as assembly, maintenance inspections, and replacement of units/expendable

parts.

Activities to be carried out by site maintenance personnel:

Amusement equipment/vending machine assembly, maintenance inspection and replacement of units/expendable

parts.

Other qualified professionals:

Persons employed by amusement equipment manufacturers, or involved in design, production, testing or mainte

nance of amusement equipment. The individual should have either graduated from technical school or hold similar

qualifications in electrical/electronics/mechanical engineering.

Activities to be carried out by other qualified professionals:

Amusement equipment/vending machine assembly, repair/adjustment of electrical/electronic/mechanical parts.

Definition of 'Site Maintenance Personnel or Other Qualified Individuals

Servicing and maintenance work of the contents herein stated should be

performed by the SERVICEMAN stipulated as per IEC Standard. Those who do not

have technical expertise and knowledge other than the SERVICEMAN are not

allowed to perform the work herein stated. Executing aforementioned work by

such non-technical personnel can cause serious accidents that may endanger life.

Summary of Contents for MISSION IMPOSSIBLE ARCADE








































































































































































Search results

Summary of Contents for MISSION IMPOSSIBLE ARCADE

Reviews:

Related manuals for MISSION IMPOSSIBLE ARCADE

Brands by name

Popular brands

Sega MISSION IMPOSSIBLE ARCADE, Owner'S Service Manual

Search results

Summary of Contents for MISSION IMPOSSIBLE ARCADE

Reviews:

Related manuals for MISSION IMPOSSIBLE ARCADE

Brands by name

Popular brands