background image

 
 

 

 

10 von 28 

 

 

Technical data 

 

Chipcard Interfaces 

Customer Card 
Contactless 

ISO 18092 (NFC) 

Customer Card 
Contact-based 

ISO 7816 (EMV) via 
Contact-based card reader 

Dealer Card 

ISO 7816 (EMV) via 
Plug-In-Sockel ID000 (1x) 

Data Transmission

 

 

via Mobile Network 

RTC & Tamper Protection

 

 

Battery buffered 

Software-Update

 

 

Via Mobile Network 

Interfaces

 

Vending Machine 
Controller 

MDB/IPC Level 02/03  
(optional USB) 

Terminal 
Managementsystem 

2G .. 4G Modem 

Cardholder 

NFC Antenna 
4 LED Status green 
Display Vending Machine 
Acoustic signal transmitter 
Optional card reader 

Service technician 

2 Keys  Service Menu   
2 LEDs Status controller  
              red / green  
1 LED Status Modem green 
1 LED Status NFC red 

Extensions

 

MDB Master 

To connect:  
MDB Display,   
MDB Bill Validator  
MDB Coin Changer 

Bluetooth 

To connect: 
BLE-Module 

 

 

Power Supply 

 

8,0 V to 42,5 V DC 

Power Consumption

 

Stand-By 

typ.  2,5mA (@ 13,8V) 

Operation 

typ.  125mA (@ 13,8V) 

Environmental conditions 

Operating 
Temperature 

-25 to +70 °C 

Humidity 

Up to 100 % 

Dimensions

 

Terminal Electronics  85 x 90 x 18 mm (LxBxH) 
NFC Antenna 

98 x 98 x 13 mm (LxBxH) 

Battery

 

 

Li Battery  (CR2032) 

Connectors

 

MDB-Slave 

JST S7B-PH-SM4-TB 

MDB-Master 

JST S6B-PH-SM4-TB 

Card Reader 

AMC170F-26POL 

USB-OTG 

USB-Micro-AB 

Antenna NFC 

MCX 

LED NFC 

JST SM12B-GHS-TB 

BLE-Modul (optional)  JST SM10B-GHS-TB 
Antenna Modem 

MMCX 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 3 

 KarL4 Technical data 

Summary of Contents for Garz & Fricke KarL4





























Reviews: