ENFORCER IP Fixed Cameras
SECO-LARM U.S.A., Inc.
29
The screen is blank
Check that the camera is powered up
Check that the power supply’s polarity is correct
Check that the monitor is powered up
Check that the video cable connecting the camera to the monitor is connected
properly
The screen image is dim
Clean the lens using a soft, clean cloth
Check that the light source is adequate
Strong backlight is overpowering the image
Change the D-WDR or Backlight settings
Image has too much digital noise
Change the DNR settings
The screen image is distorted
Change the position of the camera
Motion detection is not activated
Activate MOTION DET in the Setup Menu
Properly define the motion detection area
IR LEDs do not turn on
Check that the correct power supply is in use
Troubleshooting:
SECO-LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
Phone: (949) 261-2999 | (800) 662-0800 Email: [email protected]
PICRN3
MI_EV-Nx506-2W4Q__WM_201230.docx
NOTICE:
The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM reserves the right to change specifications without notice.
SECO-LARM is also not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2021
SECO-LARM U.S.A., Inc. All rights reserved.
WARRANTY:
This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for three (3) years from the date of sale to the
original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This
Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty
installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s option. In no event shall
SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any kind to the purchaser or anyone else.
IMPORTANT:
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and statutes related to monitoring and
recording audio and video signals. SECO-LARM
will not be held responsible for the use of this product in violation of any current laws or statutes.
FCC COMPLIANCE STATEMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE
HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION.
Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the
device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.
WARNING:
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause a fire or electrical shock. Do not open the case of this device, as
there are no user-serviceable components inside
California Proposition 65 Warning:
These products may contain chemicals which are known to the State of California to cause cancer and birth defects or other reproductive
harm. For more information, go to
www.P65Warnings.ca.gov
.
