ENFORCER Voice Dialer
10
SECO-LARM U.S.A., Inc.
Testing the Auto Dial Function:
To test the auto dial function, while in standby mode, press and hold the [PROG] button for at least
two seconds. When you hear a ‘beep’ tone, enter the memory location (1~5) of the number you
wish to test. The voice dialer should then dial the chosen number.
Resetting the Voice Dialer:
To reset the Voice Dialer, press and hold the [PROG] button and use a pen or paper clip to press
the [RESET] button located near the battery receptacle cover on the back of the unit and release.
The unit will return to the factory preset PIN number (000). All other user programmed settings
except the date and time will be retained.
Operating the Voice Dialer:
Arming and Disarming the System:
1.
To
arm the system
, enter the PIN number and press the [ARM/DISARM] button.
The dialer will sound three short “beeps” and the words “ARM” will appear on the LCD screen.
After 60 seconds, there will be a single “beep” tone to indicate that exit delay time has passed
and the alarm is now fully armed.
During the 60-second delay time after the system is armed, if the system detects trigger 3
indicating an open door or window, a “beep” tone sounds for 5 seconds, the reminder “CLOSE
PLEASE” appears on the LCD screen, and the word “TRIGGER” flashes. If, after 60 seconds,
that door or window is not closed, the alarm will sound and auto dialing will commence.
After the delay, when the system is fully armed, if a door or window connected to the alarm is
opened, the LCD screen will flash the word “TRIGGER”. After the adjustable entry delay time
has passed, the siren will begin to sound (30 seconds on and 30 seconds off) and auto dialing
will commence according to the programmed sequence and cycle times.
Line Seizure:
If the telephone line that the dialer is connected to is in use, the dialer will seize the line,
disconnecting the current call, to dial out. This ensures that the dialer is able to dial emergency
numbers promptly.
Note:
For proper operation, the line to the wall jack must be connected to the “LINE” jack of
the dialer. A telephone extension, if used, may be connected only to the “TEL” jack of the
dialer.
ENFORCER Voice Dialer
SECO-LARM U.S.A., Inc.
7
Deleting a Stored Phone Number
1.
Enter the PIN number and press the [PROG] button twice or until “MEMORY” flashes on the
LCD screen.
2.
Press the [ARM/DISARM] button to accept.
3.
Press the [#/DOWN] or [*/UP] button to select the number you wish to delete.
4.
Press the [DEL/PAUSE] button to delete the number.
5.
Press the [#/DOWN] or [*/UP] button to select other setup categories or press the [PROG]
button until the programming icons disappear to exit the setup mode.
Learn
This function is unused.
Setting the Siren Function
This setting allows the user to choose between an audible alarm when triggered, or a ‘silent alarm’
while dialing the emergency numbers. The factory default is “ON”.
1.
Enter the PIN number and press the [PROG] button four times or until the alarm icon
(
) flashes on the LCD screen.
2.
Press the [ARM/DISARM] button to accept. The dialer will “beep” once.
3.
Press the [#/DOWN] or [*/UP] button to select either “SOUND ON” or “SOUND OFF” and press
the [ARM/DISARM] button to accept.
4.
Press the [#/DOWN] or [*/UP] button to select other setup categories or press the [PROG]
button until the programming icons disappear to exit the setup mode.
Programming the Voice Dialer, continued:
Example 2
– To store a number with area code 1-949-555-1234, and an office extension #200
(where the PBX requires a 2-second pause before the extension): After scrolling to the desired
number location, enter ‘19495551234,’ press the [DEL/PAUSE] button for 2 seconds until the
letter ‘F’ appears on the LCD screen, press the [#/DOWN] button for 2 seconds until the ‘
┘
’
appears on the LCD screen, enter ‘200,’ and press the [ARM/DISARM] button.
Example 3
– To store a local number 555-2858: After scrolling to the desired number location,
enter ‘5552858’ and press the [ARM/DISARM] button.
5.
Repeat for the other numbers to be stored (up to 5 total).
6.
Press the [#/DOWN] or [*/UP] button to select other setup categories or press the [PROG]
button until the programming icons disappear to exit the setup mode.
Note:
If the dialer is programmed to call a voice pager service which requires operator assistance, the
service should be notified in advance regarding the meaning of the message. Consult local authorities
concerning the permissibility of automatically dialing their emergency numbers before programming.
