ENFORCER Voice Dialer
12
SECO-LARM U.S.A., Inc.
Note:
Should the user have difficulty activating functions remotely by telephone, there may
be too much ambient noise interference. Try pressing the code key again, or move to a
quieter location as ambient noise above 68dB may affect the auto dialer’s ability to detect
the tone signal.
3.
FUNCTION EXPLANATIONS
LISTEN IN – Pressing [1 #] allows a user to hear sound in the room for 50 seconds. A “beep”
will sound at 30 seconds to remind the user that the listen in time will soon end. Pressing [1 #]
again will reset the 50-second period, and entering any other key code will end monitoring and
perform the function. If there is no other key press, the call will disconnect at the end of the 50
seconds.
BROADCAST – Pressing [2 #] allows a user to speak to the person in the room for 50
seconds. A ‘beep’ will sound at 30 seconds to remind the user that the time will soon end.
Pressing [2 #] again will reset the 50-second period and entering any other key code (such as
[1 #], Room Monitor) will end broadcasting and perform the other related function. If there is no
other key press, the call will disconnect at the end of the 50 seconds.
Note:
Alternating between “Listen In” and “Broadcast” may be useful for a “conversation”
with the room occupant, but a user cannot speak and listen at the same time.
END CALL - Pressing [3 #] will end the call.
ARM SYSTEM – Pressing [5 #] during a user callback will arm the system, confirming with
three short “beeps,” and automatically hang up. If there are 5 rapid “beeps” after three short
“beeps,” it means a door/window is not closed. The dialer will then give 5 seconds to disarm
the system.
DISARM SYSTEM – Pressing [6 #] will disarm the system and automatically hang up.
Note:
If the user enters an incorrect password or key code, the voice dialer will sound 5
“beeps” and automatically hang up.
Operating the Voice Dialer, continued:
Remote Control by Telephone – Remote Control by User Call-In (Call Back), continued:
C.
Press one of the following function codes to control the system remotely:
Function
Press key code
Listen in
1 #
Broadcast
2 #
Arm system
5 #
Disarm system
6 #
The user should hear a “beep” in response. If not, enter the function code again.
ENFORCER Voice Dialer
SECO-LARM U.S.A., Inc.
5
Installing the Voice Dialer, continued:
1.
Select a location for the dialer near a standard electrical outlet (if user-supplied 12VDC
adapter is to be used), a telephone wall jack, and the alarm control panel, but out of sight. The
dialer should not be exposed to direct sunlight or rain, and must not be mounted near heat
sources such as radiators, heating ducts, or stoves.
2.
For wall-mount, use the wall mounting template to
drill holes and attach 3 screws into the wall at the
desired location. For convenience, 5~6ft (1.5~2m)
above the floor is recommended (Fig. 1).
3.
Remove the cable cover and battery cover from
the back of the voice dialer (Fig. 2).
4.
Install a 9VDC backup battery (not included).
Reattach the battery cover.
5.
Connect the dialer to up to three detectors or
groups of detectors in series using the connection
terminals as shown in the wiring diagram (see pg.
3). The dialer can also be connected to three
separate alarm control panel outputs of a separate
alarm system. When Trigger 3 is used, the jumper
connection to ground must be removed.
6.
Power:
a.
If the dialer is to be powered from the alarm
control panel, connect the alarm power outputs
to the DC Plug-to-terminal block (included) and
plug into the dialer’s DC power jack (see pg. 3).
b.
If using a 12VDC adapter (not included), plug
the adapter into the dialer’s DC power jack.
7.
Connect one end of the included telephone cable to
an existing Touch-Tone line wall socket, and the
other end to the dialer’s “LINE” jack. The wall socket
line must be connected to the dialer’s “LINE” jack for
proper operation. Optionally, connect an extension telephone using the telephone’s cable (not
included) to the “TEL” jack (Fig. 3). Reattach the cable cover.
8.
If an external alarm is desired, connect according to the wiring diagram (see pg. 3).
9.
For wall installation, place the unit over the heads of the screws installed in step 2 (Fig. 1) and
slide down. Check that the unit is firmly attached and tighten or loosen the screws as needed.
10.
Once all connections are made, the dialer is ready to be programmed.
Fig. 3
Fig. 1
5~6ft
(1.5~2m)
9VDC Battery
(not included)
Fig. 2
Cable
Cover
Battery
Cover
