SecEng SED-64 Installation & User Manual Download Page 6 | Manualshive

Page: 6 / 30

SecEng SED-64 Installation & User Manual Download Page 6

6

SIM Card Installation

Check SIM card Operation in Mobile phone

SIMM CARD

Place the SIM card into any Standard GSM phone.

Telstra , Optus ,Vodafone Cards will work. “3” (Hutchison)

network WILL NOT WORK as it is a 3G ONLY network that
does not support GSM.

Warning:

Ensure you have the correct pin number. Entering the

wrong PIN will PUK lock the SIM which will then need to be
returned to the vendor for reprogramming.

Disabling the PIN on the SIM card

To disable the PIN go to the mobile phone security menu

and select

PIN OFF

Unlocked

SIMM CARD

1.2

If the phone requests you to enter a pin number then
the SIM card is

PIN LOCKED

NOTE:

The SIM card PIN request must be disabled
before it can be used in the SED-64

Install the SIM card in the SED-64 as shown in the
Installation (Is the SIM in the right side up) see
1.1

1

3

Once done re-test by turning the phone OFF
then ON. The pin code should not be requested.

Ensure that the SIM Card does work and that a call
can be conducted from the Mobile Phone.

Test for signal strength (min 3 bars) at the alarm
location with the mobile phone.

4

2

«
...
4
5
6
7
8
...
»

Summary of Contents for SED-64































Reviews:

No comments