Sealite SL-07 Series Installation & Service Manual Download

Page: 20 / 36

Latest products and information available at www.sealite.com

SL07, SLC310 & SLC410

Compact 3-5nm+ Solar Marine Lanterns

All Sealite boards are fitted with two Indicator LED’s. These are positioned near the Flash Code Rotary

Switches. Use the table below to help determine operational status.

Yellow LED

Lantern Status

Lantern Comment

OFF

Normal

OFF

Lantern is in Daylight and in Dusk till Dawn mode or in

Standby Mode

Flashing

ON 0.15 seconds

OFF 0.15

seconds

Normal

OFF

Light is activating and will turn on after detecting 30

seconds of continuous darkness.

Flashing

2 x quick flashes

every 2 seconds

(Heartbeat)

Normal

Lantern is in Normal operating condition. It is not

connected to any GPS synchronisation.

Flashing

ON 1.5 seconds

OFF 1.5 seconds

Normal

Normal operating condition. Lantern is synchronised to

GPS-enabled lanterns.

Flashing

1 x quick flash

every 2 seconds

Normal

Lantern is ‘re-syncing’ with GPS.

The lantern re-sync’s with the GPS every 15 minutes.

Flashing

2 x quick

flashes every 11

seconds

Normal

Lantern is a Hard Wire Synchronisation Slave.

Red LED

Lantern Status

Lantern Comment

OFF

Normal

Normal Battery Voltage

Flashing once

every 1.6

seconds

Battery Voltage

is 12 – 12.5V

Battery Voltage is between 12 – 12.5V

Flashing twice

every 2 seconds

Battery Voltage

is 11.5 – 12V

Battery Voltage is between 11.5 – 12V

Flashing 3 x

times every 2

seconds

Battery Voltage

is 10.5 – 11.5V

Battery Voltage is between 10.5 – 11.5V

Flashing 4 x

times every 2.5

seconds

Battery Voltage

is 10.0 – 10.5V

Battery Voltage is between 10.0 – 10.5V

Flashing 5 x

times every 3

seconds

Battery Voltage

is less than

10.0V

Battery Voltage is at less than 10.0V

Fixed-on

Flat Battery

(<10V)

OFF

Flat Battery cut-off is now operational and the lantern

will be off. Battery must receive charge (above 12V) and

lantern must see daylight for at least 1 minute before

resuming normal operation.

Flashing

ON 1.5 seconds

OFF 1.5 seconds

Battery Voltage

is above 13.5V

Battery Voltage is above 13.5V. this may indicate a

problem with the solar regulator.

Summary of Contents for SL-07 Series





































Search results

Summary of Contents for SL-07 Series

Reviews:

Related manuals for SL-07 Series

Brands by name

Popular brands

Sealite SL-07 Series, Installation & Service Manual

Search results

Summary of Contents for SL-07 Series

Reviews:

Related manuals for SL-07 Series

Brands by name

Popular brands