Sealite SL-07 Series Installation & Service Manual Download Page 27

Page: 27 / 36

Latest products and information available at www.sealite.com

SL07, SLC310 & SLC410

Compact 3-5nm+ Solar Marine Lanterns

The following table explains the flash codes response from the lantern:

Lantern Flash

Response

Description

One,

4 second flash

GPS disabled.

The GPS synchronisation module is

disabled. The lantern will be unable to

synchronise with other lanterns.

One,

1 second flash

GPS enabled,

not synchronised, invalid UTC

status

Initialising, stage 1

No valid time stamp data has been

received from a satellite.

Depending on the strength of the

satellites signals, it may take several

minutes to complete this stage.

Two,

1 second flashes

GPS enabled,

not synchronised, valid UTC status

Initialising, stage 2

Valid message(s) have been received

from the satellites, but still waiting for

valid time data.

Depending on the number of available

satellites, it may take up to one minute

to complete this stage.

Three,

1 second flashes

GPS enabled,

synchronised timestamp, invalid

UTC status

Initialising, stage 3

Valid time data has been received but

invalid UTC status data was detected.

It may take up to 13min to complete

this stage.

Four,

1 second flashes

GPS enabled,

synchronised to UTC time and valid

UTC

The GPS synchronisation module is

functioning correctly.

Summary of Contents for SL-07 Series





































Search results

Summary of Contents for SL-07 Series

Reviews:

Related manuals for SL-07 Series

Brands by name

Popular brands

Sealite SL-07 Series, Installation & Service Manual

Search results

Summary of Contents for SL-07 Series

Reviews:

Related manuals for SL-07 Series

Brands by name

Popular brands