Page 1
InstructIons for:
DIESEL/FLUID TRANSFER PUMP
MoDEL no's:
TP98.v2 & TP9824.v2
thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THIS PRODUCT CORRECTLY AND ONLY FOR ITS INTENDED PURPOSE. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY AND WILL INvALIDATE THE WARRANTY. RETAIN THESE INSTRUCTIONS FOR FUTURE USE.
Maintain the pump in good condition (use an authorised service agent).
familiarise yourself with the applications, limitations and potential hazards of the transfer Pump.
replace or repair damaged parts.
Use recommended parts only. Non authorised parts may be dangerous and will invalidate the warranty.
Keep the pump clean for best and safest performance.
Ensure the power supply (vehicle battery) corresponds with the requirements of the pump. tP98 12Volt, tP9824 24Volt Dc power supply.
DO NOT
pull or carry the unit by its cables and do not pull the negative and positive clamps from the battery terminals.
DO NOT
start or stop the pump by connecting or disconnecting the battery clamps
Ensure that there is more liquid in the suction tank than will be pumped.
Ensure that the capacity of the receiving tank is sufficient to hold the pumped fuel.
Wear safety goggles and gloves, and protective clothing when working around fuel. A full range of personal safety equipment is available
from your local sealey dealer.
use the pump in an appropriate working area for its function. Keep area clean and tidy and free from unrelated materials, and ensure there
is adequate lighting.
Maintain correct balance and footing.
Ensure the floor is not slippery and wear
non slip shoes.
Keep children and unauthorised persons away
from the working area.
DO NOT
‘dry run’ the pump without fuel.
this will damage the pump’s internal
components and will invalidate your warranty.
DO NOT
operate the pump continuously for
more than 30 minutes. the duty cycle of the
unit is 30 minutes, after which the motor must
be left to cool down.
DO NOT
run the unit for more than 2-3
minutes with the delivery nozzle closed.
DO NOT
smoke or allow a spark, or flame in
the vicinity of the battery or pump.
DO NOT
operate the pump with wet hands.
DO NOT
use the pump where explosive or
flammable vapours may be present.
DO NOT
tamper
with the pump connections.
DO NOT
allow the pump to run dry.
WARNING!
DO NOT
use the unit to pump the
following fluids:
Petrol, flammable liquids with PM <55°C,
water, alimentary liquids with viscosity >20
cSt., corrosive chemicals and solvents.
WARNING!
The warnings, cautions and instructions referred to in this manual cannot cover all possible conditions and situations
that may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but
must be applied by the operator.
1. SAFETY INSTRUCTIONS
2
.
INTRODUCTION
Electric 12 or 24Volt pump kit with battery clips. High flow pump unit with bypass valve, suitable for filling diesel vehicles in the field. cast iron
pump body with anti-corrosion finish. Includes integral on/off switch, delivery hose with manual delivery nozzle and filter.
Model TP98
Pump power . . . . . . . . . . . . . . . . . .12 Volts (35 Amps, 240 Watts).
Duty cycle. . . . . . . . . . . . . . . . . . . .30 minutes
speed . . . . . . . . . . . . . . . . . . . . . . .2000rpm
Model TP9824
Pump power . . . . . . . . . . . . . . . . . . .24 Volts (18 Amps, 240 Watts).
Duty cycle. . . . . . . . . . . . . . . . . . . . .30 minutes
speed . . . . . . . . . . . . . . . . . . . . . . . .2000rpm
tP98.V2, tP9824.V2 Issue no.2 - 17/02/09
