![background image](http://html.mh-extra.com/html/sealey/spi1224/spi1224_owners-manual_1224248008.webp)
•
9
•
AUTOMATIC CHARGING MODE
When an Automatic Charge is performed, the charger switches to the Maintain Mode
automatically after the battery is charged. For a battery with a starting voltage under 1 volt,
use a manual charger to pre-charge the battery for five minutes, to get additional voltage
into the battery.
ABORTED CHARGE
If charging cannot be completed normally, charging will abort. When charging aborts, the
charger’s output is shut off, the
GREEN LED
will flash, and the display will show
CHARGE
ABORTED-BAD BATTERY
. Do not continue attempting to charge this battery. Check the
battery and replace, if necessary.
CHARGE COMPLETION AND MAINTAIN MODE (FLOAT MODE MONITORING)
Charge completion is indicated by the pulsing
GREEN LED
and the digital display showing
FULLY CHARGED-AUTO MAINTAINING
. This indicates the charger has switched to
the Maintain Mode of operation. In this mode, the charger keeps the battery fully charged
by delivering a small current when necessary.
NOTE:
If the charger has to provide its
maximum maintain current for a continuous 12 hour period, it will go into Abort Mode (see
Aborted Charge
section). This is usually caused by a drain on the battery, or the battery
could be bad. Make sure there are no loads on the battery. If there are, remove them. If
there are none, have the battery checked or replaced.
MAINTAINING A BATTERY
The SPI1224 maintains 12V and 24V batteries, keeping them at full charge.
It is not
recommended for industrial applications.
NOTE:
The maintain mode technology allows you to safely charge and maintain a healthy
battery for extended periods of time. However, problems with the battery, electrical
problems in the vehicle, improper connections or other unanticipated conditions could
cause excessive current draws. As such, occasionally monitoring your battery and the
charging process is recommended.
FAN
Your charger is equipped with a fan. It is normal for the fan to run while the charger is charging.
Keep the area near the charger free of obstructions, to allow the fan to operate efficiently.
13. DISPLAY MESSAGES
SELECT CHARGE MODE
(No LED lit) – Waiting for user to select battery type. If no
button pressed, charger will enter 12V charge mode after 10 minutes.
12V-REGULAR CHARGE-PRESS FOR 24V-DOUBLE FOR RECONDITION
(No LED lit) –
Charging will begin for 12V battery. Press again to change to 24V battery type, double click
button to change to 12V Recondition mode.
12V-CONNECT CLAMPS-PRESS FOR 24V-DOUBLE FOR RECONDITION
(No LED lit) –
No battery connected. Press again to change to 24V battery type, double click button to
change to 12V Recondition mode.
12V-RECONDITION CHARGE-PRESS FOR 24V-DOUBLE FOR REGULAR
(No LED lit) –
12V battery Recondition mode charge will start after battery is connected. Press again to
change to 24V battery Recondition mode, double click button to change to 12V charge
mode.
24V-REGULAR CHARGE-PRESS FOR 12V-DOUBLE FOR RECONDITION
(No LED lit) –
Charging will begin for 24V battery. Press again to change to 12V battery type, double click
button to change to 24V Recondition mode.
24V-CONNECT CLAMPS-PRESS FOR 12V-DOUBLE FOR RECONDITION
(No LED lit) –
No battery connected. Press again to change to 12V battery type, double click button to
change to 24V Recondition mode.
24V-RECONDITION CHARGE-PRESS FOR 12V-DOUBLE FOR REGULAR
(No LED lit) –
24V battery Recondition mode charge will start after battery is connected. Press again to
change to 12V battery Recondition mode, double click button to change to 24V charge mode.
Summary of Contents for SPI1224
Page 11: ... 12 ...