1.3.5. DO regularly inspect power supply leads, plugs and sockets for wear, damage or loose connections.
1.3.6. DO check that the voltage marked on the product is the same as the power supply
to be used and check that all fused plugs are fitted with the correct capacity fuse.
1.3.7. DO NOT pull or carry the appliance by attached leads.
1.3.8. DO NOT pull plug from socket by the power cable.
1.3.9. DO NOT use worn or damage leads, plugs or connections. Immediately replace,
or have repaired, by qualified persons. A U.K. 3 pin plug with ASTA/BS approval
is fitted. In case of damage, cut off and fit a new plug according to the following
instructions (UK only - see diagram right).
a) Ensure the unit is correctly earthed via a three-pin plug.
b) Connect the Green/Yellow earth wire to the earth terminal E.
c) Connect the Brown live wire to live terminal L.
d) Connect the Blue neutral wire to the neutral terminal N.
e) Ensure cable outer insulation extends past cable clamp and that clamp is tightened.
2. INTRODUCTION & SPECIFICATIONS
No Load Speed . . . . . . . . . . . .0-2200rpm
Impact Rate . . . . . . . . . . . . . . .0-2900bmp
Maximum torque . . . . . . . . . . . . .900kg/cm
Weight . . . . . . . . . . . . . . . . . . . . . . .1.7kg
Battery Pack . . . .12V (Model No CB1210)
Blue -
neutral
wire
Yellow & Green -
earth wire
Brown - live
wire
3. OPERATING INSTRUCTIONS
Note:
When new, the battery pack will have been shipped in a low charge state. It will take longer to charge initially, and several subsequent charges
may also take a little longer than when the battery pack reaches its optimum performance. To charge remove battery pack from case and charge
as below:
3.1.
CHARGING THE BATTERY PACK
3.1.1. To remove the battery pack (fig 1.1) from wrench, depress the two side release clips (2).
p
p
p
WARNING! Do not touch metal terminals.
3.1.2. Place wrench in carrying case and remove the battery charger.
3.1.3. The battery pack and charger have the positive (+) and negative (-) terminals marked.
Align the correct terminals and insert the battery into slot (fig 2.A).
Note: the battery pack is designed so that it will only enter the charger unit the correct way
.
When placed in the charger, a very slight downward pressure will seat the pack firmly into the
power terminals.
The LED (fig 2. B) will light up RED and remain whilst charging.
3.1.4. When charge is complete the LED colour will change to Green.
NOTE:
The charge time should be approximately 1 hour.
3.1.5. When charged, remove the battery from the charger and use accordingly.
Disconnect the battery charger from the mains power supply and store in case.
Cable clamp
FUSE RATING
THE PLUG FITTED TO PRODUCT
MUST BE EQUIPPED WITH A
3 Amp FUSE
1.4. BATTERY CHARGER SAFETY INSTRUCTIONS.
p
p
p
WARNING! DO NOT attempt to charge any battery other than that supplied for the wrench. Other types of batteries may explode!
3
All mains electrical supply safety features must be followed as described in 1.3. above.
3
Disconnect the charger from the mains power supply when not in use.
7
DO NOT charge battery if room temperature is below 41
O
F (5
O
C) or above 104
O
F (40
O
C)
7
DO NOT expose the charger to damp or wet conditions.
7
DO NOT pull or carry the charger by the power lead.
7
DO NOT operate the charger if it has been dropped, or has received a sharp knock, or is damaged. Take charger to an authorised agent.
or replace the charger.
7
DO NOT dismantle the charger as this may cause damage and/or personal injury and will invalidate your warranty.
7
DO NOT insert foreign objects or material into the hole reserved for the battery pack.
7
DO NOT recharge a second battery pack immediately after charging the first. Consecutive charging will overheat the charger. Allow the
unit to cool for 15 minutes before charging the next pack.
7
DO NOT attempt to connect two chargers together.
3
Store the charger in the same manner as battery pack in 1.2.
Powerful and compact cordless impact
wrench fitted with electronic variable
speed control. The forward and
reverse controls are integrated into
housing for ease of use. Superbly
balanced tool with plenty of power for
workshop applications. Includes 12
Volt Ni-Cad battery pack and charger.
CP1210/IW - 0016 - (1) - 040700
fig 1.
fig 2.
