Seakeeper 7HD Installation Manual Download Page 31 | Manualshive

Page: 31 / 47

Seakeeper 7HD Installation Manual Download Page 31

INSTALLATION

MANUAL

Product:

Document #:

Rev:

Page:

SEAKEEPER 9 / 7HD

90222

6

5 of 11

Section 2: ELECTRICAL INSTALLATION

ii. The recommended wiring is shown in Figure 6. Refer to Figure 4 for Cable 5

wire connections.

FIGURE 6

– RECOMMENDED WIRING FOR SEAWATER PUMPS NOT 230 VAC

d. If CABLE 5 is not used, bundle cable and secure to forward brace or other area

nearby  which  will  not  come  in  contact  with  moving  parts  during  Seakeeper
operation.  Do NOT cut CABLE 5 as it contains live voltage when the Seakeeper is
in  operation.    The  Seakeeper  ships  with  CABLE  5  permanently  sealed  at  end  of
cable  with  protective  cap  in  the  event  it  is  not  used.    Do  NOT  remove  CABLE  5
from Drive Box as moisture will be free to enter box through open cable gland and
corrode internal electronic components.

Cable 5 contains live voltage when the Seakeeper is in operation. Do
NOT cut Cable 5. Do not remove Cable 5 from Drive Box.

«
...
29
30
31
32
33
...
»

Summary of Contents for 7HD
















































Reviews:

No comments