Seakeeper 7HD Installation Manual Download Page 45

Page: 45 / 47

INSTALLATION

MANUAL

Product:

Document #:

Rev:

Page:

SEAKEEPER 9 / 7HD

90222

1 of 3

Section 5: INSTALLATION CHECKLIST AND SUPPLIES

Please Complete Checklist and E-mail to

[email protected]

or telefax to +1.410.326.1199

5.0 Installation Checklist

Mechanical Checklist (reference Installation Manual Section 1)



Seakeeper Foundation Installed in Hull



Foundation bolts torqued to specification

Electrical Checklist (reference Seakeeper Drawing 90257 & Installation Manual Section 2)

Mount Components



Display (near helm)

Connect Customer Supplied Cables



Cable 1 (Seakeeper supplied)

– Connect Cable 1 from Seakeeper 24VDC power

at customer supplied connection box, or
directly to a circuit breaker.



– Plug connector of Cable 1 into mating

connector on the Seakeeper wire harness



Cable 6 (customer supplied)

– Install lugs on both ends of customer supplied

10 AWG ground cable



– Connect one end of Cable 6 to nearest vessel

ground and other end to Seakeeper rear brace

Connect Seakeeper Supplied Cables



Cable 2 (Seakeeper supplied)

– Connect Cable 2 from Drive Box to 230 VAC

single phase at customer supplied connection
box or directly to circuit breaker



Cable 5 (Seakeeper supplied)

– Connect Cable 5 from Drive Box to customer

supplied 230 VAC seawater pump

Summary of Contents for 7HD
















































Search results

Summary of Contents for 7HD

Reviews:

Related manuals for 7HD

Brands by name

Popular brands

Seakeeper 7HD, Installation Manual

Search results

Summary of Contents for 7HD

Reviews:

Related manuals for 7HD

Brands by name

Popular brands