Seagull Models SEAX139 Assembly Manual Download Page 7 | Manualshive

Page: 7 / 20

background image

WWW.SEAGULLMODELS.COM

7

M2 clevis.

Hex nut.

Fuel tubing.

Repeat steps to install the remaining ai-

leron control horn and pushrod.

1) The blind nuts for securing the land-

ing gear are already mounted inside the

fuselage.

4) Use hobby scissors and a hobby knife

to trim the landing gear fairings. Leave

the size of the fairings slightly over-sized.

2) Using the hardware provided, mount

the main landing gear to the fuselage.

3) Place the fuselage inverted on the

workbench in a suitable stand. Set the

landing gear in place and use a screw-

drive to secure the landing gear to the fu-

selage using bolts M4x15mm and wash-

ers. Make sure to use the threadlock on

the bolts so they don’t vibrate loose.

INSTALLING THE MAIN LANDING

GEAR TO FUSELAGE.

M4x15mm

Thread locker glue.

C/A glue.

M4x15mm

«
...
5
6
7
8
9
...
»

Summary of Contents for SEAX139





















Reviews:

No comments

Related manuals for SEAX139

Brand: Horizon Hobby Pages: 19

HO Scale Under The Ties 309

Brand: Kadee Pages: 2

Brand: Velleman Pages: 8

U.S. GENERAL Junior 56515

Brand: Harbor Freight Tools Pages: 8

Hellcat Little Nugget

Brand: H-KING Pages: 18

3-in-1 Ride-On Firetruck

Brand: Mega Bloks Pages: 6

Brand: Fisher-Price Pages: 20

Brand: Tadano Pages: 16

Brand: Jamara Pages: 12

Brand: PIKO Pages: 12

Brand: NOCH Pages: 2

T-34/85 Standard M 1:16

Brand: XciteRC Pages: 40

Mikey's Swing-Arm Bike 12009

Brand: K'Nex Pages: 23

Sort & Discover Car

Brand: VTech Baby Pages: 11

Brand: KANGKE INDUSTRIAL Pages: 12

Baby s Light-Up Laptop Pink

Brand: VTech Pages: 13

Winnie the Pooh - Play & Learn Laptop

Brand: VTech Pages: 10

Brand: VTech Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands