Seagull Models SEAX139 Assembly Manual Download Page 11 | Manualshive

Page: 11 / 20

background image

WWW.SEAGULLMODELS.COM

11

11

COWLING.

The cowl can now be secured to the fuse-

lage using the four 2x6mm metal screws.

1) Locate the items for this section of the

manual.

Holes.

Please see below pictures.

INSTALLING THE PROPELLER.

The propeller should not touch any

part of the spinner cone. If it does, use a

sharp modeling knife and carefully trim

away the spinner cone where the propel-

ler comes in contact with it.

HINGING THE ELEVATOR.

«
...
9
10
11
12
13
...
»

Summary of Contents for SEAX139





















Reviews:

No comments

Related manuals for SEAX139

Brand: B Pages: 2

Brand: Fisher-Price Pages: 8

Lego 123 Sesame Street 21324

Brand: Glow Bricks Pages: 13

Explore Dinosaurs National Geographics KIDS

Brand: InspirationWorks Pages: 2

harbour tug FAIRPLAY

Brand: ROBBE Pages: 14

B&O 0-4-0 DOCKSIDE

Brand: AML Pages: 8

Brand: Eduard Pages: 10

Tribute EP 3D Profile

Brand: E-FLITE Pages: 40

ULTIMATE 20-300 ARF-QB

Brand: AeroWorks Pages: 94

UMX Sbach 342 3D

Brand: E-FLITE Pages: 17

Brand: Eduard Pages: 9

GAIA 160HY-Hybrid

Brand: Foxtech Pages: 19

Brand: LEGO Pages: 23

SOUTHERN PACIFIC 2-10-2 F4

Brand: Accucraft trains Pages: 6

Brand: Eduard Pages: 2

EP F-20 Tigershark ElectriFLy

Brand: GREAT PLANES Pages: 16

Brand: Funkey Pages: 6

Obsession Speedboot

Brand: Jamara Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands