Seagull Models SEAX139 Assembly Manual Download Page 5 | Manualshive

Page: 5 / 20

background image

WWW.SEAGULLMODELS.COM

5

3) Use a drill bit to drill the holes for the ser-

vo mounting screws.

4) Use a screwdriver to thread a servo

mounting screw into each of the holes to cut

threads in the surrounding wood. Remove

the screw before moving to the next step.

6)Secure the servo using the screws provided

with the servo and a screwdriver. The output

shaft of the servo will align with the opening

in the cover.

7) Fit the servo horn to the servo so it is per-

pendicular to the servo.

8) Use string or dental floss to secure a servo

extension to the aileron servo lead.

5) Apply 2-3 drops of thin CA in each of the

holes to harden the surrounding wood. This

will harden the threads so the screws do not

easily strip the surrounding wood.

C/A glue.

9) Use the string to pull the extension

through the wing root.

1.5mm

«
...
3
4
5
6
7
...
»

Summary of Contents for SEAX139





















Reviews:

No comments

Related manuals for SEAX139

Brand: Tough Jets Pages: 22

Brand: Faller Pages: 12

Brand: Radica Games Pages: 2

L.O.L. SURPRISE! O.M.G. ROYAL BEE

Brand: MGA Entertainment Pages: 2

Brand: VTech Baby Pages: 10

Brand: Radio Shack Pages: 2

Brand: Uberstix Pages: 40

ZAG HEROEZ Miraculous Pixelo

Brand: Lansay Pages: 2

Ju 88A interior S.A.

Brand: Eduard Pages: 2

Super PNP F-100D Super Sabre

Brand: Flex innovations Pages: 32

Brand: BLOTZ Pages: 2

No. 9 pay as you enter

Brand: M.T.H. Pages: 23

Brand: Haute Decor Pages: 2

Doubledare Dueling Coaster

Brand: K'Nex Pages: 44

Spitfire F.Mk.22/24 landing flaps

Brand: Eduard Pages: 2

Lancaster landing flaps

Brand: Eduard Pages: 2

RC Creatures Gorilla

Brand: World Tech Toys Pages: 4

Brand: Trix Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands