Seagull Models RACER DELTA 40-46 Assembly Manual Download Page 3

Page: 3 / 27

KIT CONTENTS.

SEA307 RACER DELTA 40-46

1. Fuselage

2. Rudder

3. Cowling

4. Canopy

5. Pilot

6. Landing gear

ADDITIONAL ITEMS REQUIRED.

TOOLS & SUPPLIES NEEDED.

Thin cyanoacrylate glue.

Medium cyanoacrylate glue.

30 minute epoxy.

5 minute epoxy.

Hand or electric drill.

Assorted drill bits.

Modelling knife.

Straight edge ruler.

2mm ball driver.

Phillips head screwdriver.

220 grit sandpaper.

90° square or builder’s triangle.

Wire cutters.

Masking tape & T-pins.

Thread-lock.

Paper towels.

�

0.40-0.46 cu in 2 stroke.

�

Computer radio with 6 servos.

�

Glow plug to suit engine.

�

Propeller to suit engine.

�

Protective foam rubber for radio

system.

COMBINE THE WINGS.

Fill Epoxy.

Fill epoxy on whole wing panel, included

hole for wing tube.

Summary of Contents for RACER DELTA 40-46




























Search results

Summary of Contents for RACER DELTA 40-46

Reviews:

Related manuals for RACER DELTA 40-46

Brands by name

Popular brands

Seagull Models RACER DELTA 40-46, Assembly Manual

Search results

Summary of Contents for RACER DELTA 40-46

Reviews:

Related manuals for RACER DELTA 40-46

Brands by name

Popular brands