Seagate ST31051 Product Manual Download Page 90

Page: 90 / 200

Product Manual - Disc Drive SCSI-2/SCSI-3 Interface (Vol. 2; Ver. 2), Rev. E

_____________________________________________________________________________________

continued from previous page

Byte

Description

Invalid Command Operation Code

Logical Block Address Out Of Range

Invalid Field In CDB

Logical Unit Not Supported

Invalid Field In Parameter List

Parameter Not Supported

Parameter Value Invalid

Invalid Field Parameter - Threshold Parameter

Invalid Field Parameter - Check Sum

Invalid Field Parameter - Firmware Tag

Write Protected

Not-Ready to Ready Transition; medium may have changed

Power On, Reset, Or Bus Device Reset Occurred

Power-On Reset occurred

Parameters Changed

Mode Parameters Changed

Log Parameters Changed

Tagged Commands Cleared By Another Initiator

Medium Format corrupted

Format Failed

No Defect Spare Location Available

Parameter Rounded

Invalid Bits in Identify Message

Logical Unit has Not Self Configured yet

Target Operating Conditions have changed

Microcode Changed

Changed Operating Definition

DRAM Parity Error

Power-On or Self-Test Failure

Message Error

Internal Target Failure

Select/Reselection Failure

SCSI Parity Error

Initiator Detected Error Message Received

Invalid Message Error

Logical Unit Failed Self-Configuration

Overlapped Commands Attempted

5B*

Log Exception

5B*

Threshold Condition Met

5B*

Log Counter At Maximum

5B*

Log List Codes EXHAUSTED

RPL Status Change

Spindles Synchronized

Spindles Not Synchronized

Voltage Fault

General Firmware Error Qualifier

*Note.

Can be supported, but is a factory installed option.

Summary of Contents for ST31051









































































































































































































Search results

Summary of Contents for ST31051

Reviews:

Related manuals for ST31051

Brands by name

Popular brands

Seagate ST31051, Product Manual

Search results

Summary of Contents for ST31051

Reviews:

Related manuals for ST31051

Brands by name

Popular brands