SEA ISUZU FSR Owner'S Manual Download Page 40

Page: 40 / 56

OWNER

’

S MANUAL

(

SEA ISUZU FSR/FSD EV)

SEA-OWS-QA-004/5

ISSUE DATE:

30/05/2020

Page

•

The steering wheel operates heavily

Fault diagnosis

Handling methods

Load unbalanced toward front axle

Average the load.

The power steering fluid level is low

Top up power steering fluid.

Power steering pump is not operating.

Check Inverter Fuse (as per diagram FB01).
Check Inverter Relay is located correctly (as per
diagram FB02).

The front tire pressures are low.

Adjust to specified pressure.

•

Excessive free play in steering

Fault diagnosis

Handling methods

Front tyre pressures are low

Adjust to specified pressure.

Free play in steering box

Refer to OEM for adjustment/replacement

Kingpin bearings are worn

Refer to OEM for replacement

Worn bushes in steering linkage

Refer to OEM for replacement

The ball joints or tie rods are worn.

Refer to OEM for replacement

•

The auxiliary/low-voltage battery discharges repeatedly

Fault diagnosis

Handling methods

The battery has reached its service life.

Replace it.

Summary of Contents for ISUZU FSR

























































Search results

Summary of Contents for ISUZU FSR

Reviews:

Related manuals for ISUZU FSR

Brands by name

Popular brands

SEA ISUZU FSR, Owner'S Manual

Search results

Summary of Contents for ISUZU FSR

Reviews:

Related manuals for ISUZU FSR

Brands by name

Popular brands