SEA USA USER 2 - 24V Manual Download Page 7

USER 2 - 24V

International registered trademark n. 2.777.971

GENERAL INFORMATION

The information in this section of the manual are only for technicians or for   qualified or authorized installers.

GENERAL CHARACTERISTICS 

The   USER 2 24V control unit has been designed   to manage one or two low voltage swing gate operators with or without 
electronic limit switches.

  

It is of very small dimensions and besides the possibility to adjust motor speed,   amperemetric anti squeezing sensitivity,   leaf 
delay in closing,     pausing time, it is also possible   to manage a display,   through which it is possible to control a lot of   
management functions and   the maintenance of the control unit. The   most important change however concerns the presence of 
a BUS connector with two wires, through which it is possible to connect   accessories as photocells, flashing lamp, key switch and 
so on,... connecting only two cables with the control unit. The self- learning of working time can be done automatically.

ARRANGEMENTS 

Read attentively the installation manual as it gives important indications concerning safety, installation, use and maintenance.       

Installation, maintenance, reparation, controls and eventual putting out of function of the product must be executed by qualified 
staff only.          

  

For the security of people it is important to follow with attention all the advises and instructions in this manual. A wrong 
installation or a wrong use of the product can cause sever damages to people.

TECHNICAL SPECIFICATIONS 

Control unit power supply
Absorption   in stand by
Max. motor charge 
Max. accessories charge
Max. Flash light charge
Environment temperature 
Protection fuse (24V accessories)
Function logic
Opening/closing time
Time of pause
Thrust 
Slow down 

Input   on connecting terminal 

Output   on connecting terminal 

Board dimensions
Specifications of   optional batteries
Specifications of external enclosure 

Special accessories 

24 V

100 mA

90 W x 2

24V      250mA

24V      15W max.

-20°C   +50°C

1 (1,6mA)

Automatic / Manual / Security / Semiautom.

In selflearning in programming phase

Adjustable 
Adjustable
Adjustable 

Battery power supply / Total opening /Pedestrian 

opening adjustable / Edge/ Stop / Limit switch 

opening and closing / Encoder/ BUS accessories

Power supply accessories  24V     / Motors 24V     / 

Flashing lamp 24V      / Electric lock 12V      

156 x 100 mm

24V Pb 2Ah min.

305 x 225 x 125 mm - Ip55

Battery charger card (cod.23101105), Relay card 

for courtesy light or  bolt  lock  (cod.23101106), 

Programmer JOLLY (cod.23105276), Programmer 

OPEN (cod.23105290), Photocell SUNSET BUS 

(cod.23102075)

67410925

7

REV 02 - 06/2010

Summary of Contents for USER 2 - 24V

























Reviews: