manualshive.com logo in svg

Sea-doo GS 5644, Operator'S Manual

Share
Download
Sea-doo GS 5644 Operator'S Manual Download Page 84

82

Engine Will Not Start

OTHER OBSERVATION

POSSIBLE CAUSE

REMEDY

Engine does not turn over.

• Safety lanyard removed.

Install cap over switch.

• Burnt fuse.

Check wiring then replace fuse.

• Discharged battery.

Refer to an authorized Sea-Doo 
dealer.

• Battery connections, 

corroded or loose.

Refer to an authorized Sea-Doo 
dealer.

• Water-flooded engine.

Refer to 

Water-Flooded Engine

 in 

SPECIAL PROCEDURES.

Engine turns slowly.

• Discharged or weak 

battery.

Refer to an authorized Sea-Doo 
dealer.

Engine turns normally.

• Closed fuel tank valve 

(except RFI models)

.

Turn fuel tank valve to ON position.

• Fuel tank empty or

water-contaminated.

Refill. Siphon and fill with fresh fuel.

• Fuel filter clogged or 

water-contaminated 

(except RFI models)

.

Clean, check fuel tank for water.

• Fouled/defective spark 

plugs.

Replace.

• Misuse of choke

(except RFI models)

.

Use only with cold engine. Replace 
spark plugs.

• Fuel-flooded engine.

Refer to 

Fuel-Flooded Engine 

in 

SPECIAL PROCEDURES.

• Burnt fuel pump fuse

(RFI models)

.

Check wiring then replace fuse.

• Electrical problem

(RFI models)

.

Refer to an authorized Sea-Doo 
dealer.

smo2000-002a.book Page 82 Tuesday, September 28, 1999 12:00 PM

www.SeaDooManuals.net

Summary of Contents for GS 5644












































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands