manualshive.com logo in svg

Sea-doo GS 5644, Operator'S Manual

Share
Download
Sea-doo GS 5644 Operator'S Manual Download Page 63

61

XP, GTX and RFI Models

Rotate the watercraft 

clockwise

 (seen

from rear) to its 

right

 side for cleaning.

All Models

Clean the water intake area. If the sys-
tem is still clogged, refer to an autho-
rized Sea-Doo dealer for servicing.

CAUTION:

Inspect water intake grate

for damage. Refer to an authorized
Sea-Doo dealer for repair as neces-
sary.

Capsized Watercraft

The watercraft is designed so that it
should not turn over easily. Also two
sponsons mounted on the side of the
hull assist watercraft stability. If it turns
over, it will remain capsized.

CAUTION:

Always refer to decal lo-

cated on stern of watercraft.

GS, GTS and GTI Models

To return the watercraft upright, en-
sure engine is off, grab the inlet grate,
step on bumper rail and use your
weight to rotate the watercraft 

clock-

wise

 (seen from rear).

XP, GTX and RFI Models

To return the watercraft upright, en-
sure engine is off, grab the inlet grate,
step on bumper rail and use your
weight to rotate the watercraft 

coun-

terclockwise

 (seen from rear).

Submerged Watercraft

If the watercraft is submerged and en-
gine is water-flooded, it is strongly rec-
ommended that the watercraft be ser-
viced by an authorized Sea-Doo dealer.

Water-Flooded Engine

In the event the engine cannot be ser-
viced within a few hours, remove
spark plug cables and connect them
on the grounding device.

F06L11Y

Max. 90°

WARNING

Never crank engine with spark
plugs removed unless spark plug
cables are connected to the ground-
ing device.

F02L2EZ

F06L0DZ

smo2000-002a.book Page 61 Tuesday, September 28, 1999 12:00 PM

www.SeaDooManuals.net

Summary of Contents for GS 5644












































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands