manualshive.com logo in svg

Sea-doo GS 5644, Operator'S Manual

Share
Download
Sea-doo GS 5644 Operator'S Manual Download Page 65

63

Towing the

 

Watercraft

 

in 

Water

Special precautions should be taken
when towing a Sea-Doo watercraft in
water.

Maximum recommended towing speed
is 24 km/h (15 MPH).

When towing your watercraft in water,
pinch the water supply hose from the
impeller housing to the engine with a
large hose pincher (P/N 529 032 500).

This will prevent the cooling system
from filling which may lead to water
being injected into and filling the ex-
haust system. Without the engine run-
ning there isn’t any exhaust pressure
to carry the water out the exhaust out-
let.

CAUTION:

Failure to do this may re-

sult in damage to the engine. If you
must tow a stranded

 

watercraft

 

in

water and do not have a hose pinch-
er, be sure to stay well below the
maximum towing speed of 24 km/h
(15 MPH).

Snugly install the hose pincher on the
water supply hose as shown.

GS, GTS AND GTI MODELS

1. Hose pincher

XP MODELS

1. Hose pincher

GTX MODELS

1. Hose pincher

F01B23Y

F02E04Y

1

F08E03Y

1

F07E03Y

1

smo2000-002a.book Page 63 Tuesday, September 28, 1999 12:00 PM

www.SeaDooManuals.net

Summary of Contents for GS 5644












































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands