Sea-doo GS 5644 Operator'S Manual Download

Page: 79 / 107

Battery

Contact your authorized Sea-Doo dealer.

Antifreezing Protection

In cool regions (where freezing point
may be encountered), cooling system
should be filled with an equal part of
water and antifreeze solution.

CAUTION:

Always use ethylene gly-

col antifreeze containing corrosion
inhibitors specifically recommended
for aluminums.

GTS Models

Install a hose pincher to engine drain
hose near the PTO flywheel guard.

TYPICAL

1. Hose pincher installed on engine drain hose

Install coupler hose to fitting spigot.

Install a hose pincher to engine water
outlet hose (beside fitting spigot).

1. Coupler hose
2. Hose pincher
3. Fitting spigot

Pour the antifreeze slowly mixed with
water in coupler hose until the colored
solution appears in the engine drain
hose.

Remove hose pincher.

All Models Except GTS

Install a hose pincher to engine drain
hose.

TYPICAL

1. Hose pincher installed on engine drain hose

Disconnect engine water outlet hose.

717 AND 787 ENGINES

1. Disconnect engine water outlet hose

F02E06Y

F01E1EY

1 3

F06E0DY

F06E0EY

smo2000-002a.book Page 77 Tuesday, September 28, 1999 12:00 PM

www.SeaDooManuals.net

Summary of Contents for GS 5644












































































































Search results

Summary of Contents for GS 5644

Reviews:

Related manuals for GS 5644

Brands by name

Popular brands

Sea-doo GS 5644, Operator'S Manual

Search results

Summary of Contents for GS 5644

Reviews:

Related manuals for GS 5644

Brands by name

Popular brands