background image

Operation & Maintenance Manual

──

LG958L/LG959 Wheel Loader 

 109

z

 

Check the oil level in the oil tank and the water level in the water tank. 

z

 

Add grease to the fan shaft, jointed point between front and rear frames, driving axles, jointed 

points of oscillating frame and joint points of work equipment. 

z

 

Check if there are other abnormalities. 

z

 

Refer to

 Operation and Maintenance Manual

 of diesel engine for maintenance. 

3.2 Every 50 Hours (Week) Service 

Carry out the periodic maintenance of every 10 hours with this maintenance operation at the same 

time. 

z

 

Check oil level of the gearbox, hydraulic oil tank and brake booster pump. 

z

 

Tighten all connection bolts of transmission axles. 

z

 

Check whether all connection bolts of hubs and the brake caliper are loose. 

z

 

Check all connection bolts of teeth for tightening. 

z

 

Check and lubricate the accelerator control, parking brake and gearshift control system. 

In addition, do the extra maintenance in the first 50 hours as follows: 

z

 

Check and clean the air vent of the gearbox. Check and clean the filter cartridge of the oil line 

system of the torque converter-gearbox. 

z

 

Check if there is leakage in the hydraulic system. Check and clean the air vent of the hydraulic 

reservoir. Check and clean the oil-return filter cartridge of the hydraulic reservoir. 

z

 

Check if there is leakage in the brake system. Clean the filter mesh of the oil bowl in the booster 

pump. Clean the air vent and check the brake fluid. Add them if deficient. 

3.3 Every 250 Hours (Month) Service 

Carry out the periodic maintenance of every 10 and 50 hours with this maintenance operation at the 

same time. 

z

 

Check the storage battery. Clean surface and terminals of the battery then coat Vaseline lamina. 

z

 

Check whether assembling bolts of frames are loose and welding seams are cracked. 

z

 

Check whether the front and rear axles, engine and gearbox and frame are loose.   

z

 

Check the tire pressure. Inflation pressure of front tires should be 0.39±0.01MPa while that of 

rear tires should be 0.33±0.01MPa. 

z

 

Open the water draining valve in the air tank to drain the water out. 

In addition, do the extra maintenance in the first 250 hours as follows: 

z

 

Check and clean the air vent of gearbox. Clean the oil pan of gearbox. Replace the suction filter 

cartridge in the oil pan of gearbox. Replace the filter cartridge in the oil lines of torque 

Summary of Contents for LG958L

































































































































Reviews:

Related manuals for LG958L